DSC PC580 v2 1 - Installation Manual - English - PowerSeries 4-32 Zone Control Panel
File Preview
Click below to download for free
Click below to download for free
File Data
Name | dsc-pc580-v2-1-installation-manual-english-powerseries-4-32-zone-control-panel-3457098216.pdf |
---|---|
Type | |
Size | 1.27 MB |
Downloads |
Text Preview
System Introduction Software Support PC580 uses DLS 1 v6.5 and up Zone Configuration Four fully programmable zones system expandable to eight using keypad zone inputs and wireless zones 38 access codes one master code one maintenance code duress codes two supervision codes and 32 general codes 27 zone types 8 programmable zone attributes Normally closed single EOL and double EOL zone wiring Eight wireless zones available using the PC5132 Wireless Alarm Output 700mA Supervised Bell Output current limited at 3 amps Steady or Pulsed Output Memory Does not lose programming or system status on complete AC Battery failure Outputs 2 programmable voltage outputs 19 programmable options PGM1 50mA PGM2 50mA 1.5 Amp Regulated Power Supply 550 mA Auxiliary Supply 12 VDC Positive Temperature Coefficient PTC components replace Supervision for loss of AC power low battery Internal clock locked to AC power frequency Requirements Transformer 16.5 VAC 40 VA Battery 12 volt 4 Ah minimum rechargeable sealed lead battery For household fire installations two 7Ah batteries must be in parallel to provide 24 hour of standby power Keypad Specifications Three keypads available PC1555RKZ eight zone LED keypad with zone input PC5508Z eight zone LED keypad with zone input LCD5500Z Alphanumeric keypad with zone input All keypads have five programmable function keys Connect up to eight keypads 4 wire Quad connection to Keybus Built in piezoelectric buzzer Communicator Specifications Supports major communication formats including SIA and ID Event initiated personal paging Three programmable telephone numbers Two account numbers Supports LINKS1000 cellular communication Supports LINKS2X50 Long Range Radio Transmitter DTMF and pulse dialing DPDT line seizure Anti jam feature Split reporting of selected transmissions to each telephone Supervision Features PC580 continuously monitors a number of possible trouble including AC power failure Trouble by zone Tamper by zone Fire trouble Telephone line trouble Failure to communicate Low battery condition Bell output trouble Module fault supervisory or tamper Loss of internal clock AUX Power Supply Trouble Alarm Prevention Features Audible Exit Delay Audible Exit Fault Communication Delay Urgency on Entry Delay Quick Exit Cross Zone Burglary Alarm Rotating Keypress Buffer Features Auto Arm at specified time Keypad activated alarm output and communicator test All modules connect to the system via a four wire Keybus up 1000 from main panel An event buffer which records the past 128 events with both time and date at which they occurred buffer can be using PC5400 serial interface module or viewed with LCD5500Z keypad Supports the addition of the PC5132 Wireless receiver for of wireless devices Uploading and downloading capability Local downloading capability through the use of the PC LINK Added Keybus fault protection clock and data outputs have programmed to withstand shorts to 12v to prevent panel damage Additional Devices addition to the information below see the back cover for a module compatibility table Wireless Receiver PC5132 Wireless Receiver can be used to connect up to 8 devices to the system All devices are spread spectrum MHz fully supervised devices which use standard or alkaline batteries additional devices are available They are as follows Wireless Motion Detector Wireless Universal Transmitter wireless door or window contacts to your system Wireless Smoke Detector Wireless Slimline Universal Transmitter smaller wireless door or window contact Wireless Panic Pendant personal protection to the system When used the unit will a non medical emergency to the central station Wireless Key a simple and mobile method of arming and disarming to the as well as one button access to several programmable Wireless Handheld Keypad Printer Module PC5400 Printer Module will allow the panel to print out all that occur on the system to any serial printer The will contain the time date and the event that occurred 1000 Cellular Communicator LINKS 1000 Cellular Communicator can be used three ways as the sole communicator for the panel as a for either or both telephone numbers or as a redundant to the land line communicator where the panel will call the land line and via the LINKS the LINKS2150 or LINKS2450 may be used to transmit information over a long range radio network different cabinets are available for the PC580 modules are as follows Cabinet control cabinet for the PC580 main panel Dimensions x 298mm x 78mm 11.3 x 11.7 x 3 approximately Cabinet to house the PC5400 Printer Module Dimensions x 178mm x 65mm 9 x 7 x 2.6 approximately Out of the Box verify that the following components are included in system one PC5003C main control cabinet one PC580 main control circuit board one PC1555RKZ keypad with zone input one Installation Manual with programming worksheets one Instruction Manual for the end user one hardware pack consisting of one mylar cabinet label four plastic circuit board standoffs nine 5600W one 1000W ground connection assembly one cabinet door plug 5.6K resistors 1K resistor Compatibility has not been investigated by UL Started Steps following sections provide a thorough description of how to and configure devices and zones this section completely before you begin Once you have overall understanding of the installation process carefully through each step 1 Create a Layout a rough sketch of the building to get an idea of where all detection devices keypads and other modules are to be 2 Mounting the Panel the panel in a dry area close to an unswitched AC power and the incoming telephone line Before attaching the to the wall be sure to press the four circuit board studs into the cabinet from the back After you have the cabinet to the wall stick the provided DSC logo on the front of the cabinet must complete all wiring before connecting battery or applying AC to the panel 3 Wiring the Keybus Section 2.3 the Keybus to each of the modules following the guidelines in Section 2.3 of this manual 4 Zone Wiring Section 2.8 must power down the control panel to complete all zone Please refer to Section 2.8 when connecting zones using closed loops single EOL resistors double EOL resistors zones and Keyswitch Arming zones 5 Complete Wiring Section 2.2 all other wiring including bells or sirens telephone connections and ground connections following the provided in Section 2.2 Descriptions 6 Power up the Control all zone and Keybus wiring is complete power up the panel First connect the red battery lead to the positive and the black lead to negative Then connect the AC the battery before connecting the AC panel will not power up on the battery alone 7 Keypad Assignment Section 2.5 order for keypads to be properly supervised each must be to a different slot Please follow the guidelines provided Section 2.5 when assigning keypads 8 Supervision Section 2.6 supervision of every module by the panel is automatically upon power up Please verify that all modules appear the system according to the instructions in Section 2.6 9 Programming the System Sections 4 and 5 4 explains how to program the panel Section 5 contains complete description of the various programmable features options are available and how they function The W