DSC PC6311-Installation Sheet-v1-0-English

Limited Warranty warrants that for a period of one year from the date of purchase the product shall be free defects in material and workmanship under normal use and that in fulfillment of any breach such warranty DSC shall at its option repair or replace the defective equipment upon return the equipment to its repair depot This warranty applies only to defects in materials and and not to damage incurred in shipping or handling or damage due to causes the control of DSC such as lightning excessive voltage mechanical shock water dam or damage arising out of abuse alteration or improper application of the product foregoing warranty shall apply only to the original buyer and shall be in lieu of any and all warranties whether expressed or implied and of all other obligations or liabilities on the of DSC This warranty contains the entire warranty DSC neither assumes responsibility nor authorizes any other person purporting to act on its behalf to modify or to change this nor to assume for it any other warranty or liability concerning this product no event shall DSC be liable for any direct indirect or consequential damages loss of antic profits loss of time or any other losses incurred by the buyer in connection with the pur installation or operation or failure of this product recommends that the entire system be completely tested on a regular basis However frequent testing and due to but not limited to criminal tampering or electrical dis it is possible for this product to fail to perform as expected CO MP LIANCE STATEMENT Changes or modifications not expressly approved by Digital Security Controls Ltd void your authority to use this equipment equipment has been tested and found to comply with the limits for a Class B digital device pursu to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against interference in a residential installation This equipment generates uses and can radiate radio energy and if not installed and used in accordance with the instructions may cause harmful to radio communications However there is no guarantee that interference will not occur in particular installation If this equipment does cause harmful interference to radio or television recep which can be determined by turning the equipment off and on the user is encouraged to try to the interference by one or more of the following measures Re orient the receiving antenna Connect the equipment into an outlet on a circuit different from that to which the receiver is con Consult the dealer or an experienced radio television technician for help user may find the following booklet prepared by the FCC useful to Identify and Resolve Interference Problems This booklet is available from the U S Government Printing Washington D C 20402 Stock 004 000 00345 4 the separation between the equipment and receiver Digital Security Controls Ltd cid 127 Canada cid 127 1 800 387 3630 cid 127 www dsc com in Canada 29005849 R002 PC6311 v1.0 Backbone Repeater Installation Instructions PC6311 backbone repeater extends the backbone bus up to 305 meters 1000 feet and pro isolation from downstream short circuits A maximum of three modules may be connected series from the signal source The maximum distance between two communicating devices can exceed 1220m 4000ft in a or Chain configuration Two LEDs located on the are provided for diagnostics Holes for Standoffs BLK1 YEL1 GRN1 BLK2 YEL2 GRN2 Maximum distance between two repeat 9 15VDC nom or repeater and control panel 1000 ft Maximum capacitance 50 nF 305M Maximum signal path distance with 1220m 4000ft cabinets plastic devices control panel APS interface ODS interface Diagnostics LED located on the module light when activity is detected at the input of the associated This activity is normally packets from the preceding repeater or control panel but indicate electrical noise if levels are significant Refer to the troubleshooting guide below Activity Cause Operation interference May affect communications wiring if possible interference Communications affected must be relocated are off most of the time appear to light simultaneously LED appears to light periodically LED remains off LED lights continuously LED remains off to Figure 1 and Control Panel Installation Manual for wiring details power from the system cabinet not greater than 305m 1000ft from the control panel or repeater the three standoffs into the cabinet Press firmly until standoffs click into place Align the module mounting holes over the standoffs Press module firmly into place Apply power to system and observe LED activity as indicated above Allow system to run for 15 minutes minimum If a communication problem is present a bus wire to the module in accordance with local requirements required wiring into terminals and secure in place with a flatblade screwdriver Fault will be generated within the time period PC6311 Typical Configuration devices may be connected in any combination but must not from the following guidelines longest communication path on the backbone between any two devices must not exceed 1220m 4000ft maximum distance between two series connected communicating must not exceed 305m 1000ft communication path must not have more than three PC6311 repeaters a series Interconnect Diagram must be wired using 0.6439mm 22AWG copper wire must not exceed 50nF 305m DO NOT use shielded wire 1000ft max devices 1000ft max devices 1000ft max devices 4000ft maximum any two communicating devices 1000ft devices Extended Range Termination max max installations where a great distance is required between two devices 120 1 4W 5 terminating can be connected between the YEL and GRN terminals of each device as shown above For each distance indicated above no other device can be added to the backbone