DSC PG9920-8920-4920 Installation Manual ENG FRE SPA POR - 29008668R001

D 304683 Wireless Repeater Installation PowerG Series Wireless Repeater relays digital data between PowerG control devices and a PowerG control panel extend the wireless reach of the system by relaying to devices that would normally be outside the range the control panel Messages following service messages can be transmitted by the repeater the system End of life Low Battery Supervision AC fail Tamper Setup The INSTALLER shall instruct the end user regarding the pre that shall be considered during the use of the equip Do NOT locate this product where persons will walk on the circuit cable s Do NOT use extension cords to plug in the Power Supply of equipment AVOID setting up the equipment near heaters air condition ventilators and or refrigerators Do NOT connect the RF REPEATER to electrical outlets on same circuit as large appliances Do NOT select a place that exposes your RF REPEATER to sunlight excessive heat moisture vapors chemicals or Do NOT install this equipment near water e g bath tub bowl kitchen laundry sink in a wet basement or near pool etc Do NOT install this equipment and its accessories in areas there is a risk of explosion Do NOT connect this equipment to electrical outlets con by wall switches or automatic timers avoid interfer sources equipment REPEATER Model s PGx920 shall be installed used within an environment that provides the pollution degree 2 and overvoltages category II NON HAZARDOUS LOCA indoor only The equipment is FIXED and DIRECT IN powered from the mains it is designed to be installed by Persons only The enclosure must be secured to the build structure before operation It is the end user and or installer to ensure that the disposal of the used batteries bat pack is made according to the waste recovery and recycling applicable to the intended market Only the Power Supply supplied with this equipment Use of power supplies may damage the repeater AC Socket Outlet powering the equipment shall be located the equipment and shall be easily accessible equipment has no mains on off switch The plug of the direct power supply is intended to serve as the disconnecting if the equipment must be quickly disconnected It is impera that access to the mains plug and associated mains socket out is never obstructed Ensure that Cables are positioned so that cannot occur Connected Cables must not be subject to mechanical strain To ensure the continued operation of all wireless devices performing a system default a global upload of all wireless via DLS is recommended before defaulting the sys After completing the system default download the wireless communication blinks Only GOOD or STRONG signal strengths are If you receive a POOR signal from the device re locate and re test until a GOOD or STRONG signal is received For UL ULC installations only STRONG signal levels are After installation verify the product functionality in with the compatible receivers HSM2HOST9 HS2LC HS2ICNRF P 9 and PG9920 For detailed Placement instructions refer to the control panel Guide the Device Mark for drilling Drill 4 holes with 4 supplied screws For Europe the trans has to be CE compliant with of and power limited Band MHz CE Listed 433MHz CE EN listed 868MHz FCC IC UL listed PG9920 912 919MHz Protocol PowerG Power Supply AC to AC VAC 60 Hz 9 VAC 0.35 A in the U S A VAC 50 Hz 9 VAC 0.35 A Battery 4.8 Volt 1300 NiMH rechargeable Battery Threshold 4.8 V Supply Type A to charge 80 12 Hrs voltage alarm 4.8V Current Drain when external AC power 100mA Backup Duration with charged 1300 mAh battery hours indicator Green LED lights when AC power on range 10 to 55 UL ULC only verified the to 49 Humidity up to max 93 RH non condensing LxWxD 161x161x50mm 6 7 16 x 6 7 16 x 1 3 4 maximum including battery 470g 16.5 oz RECEIVERS Band HSM2HOST4 HS2LCDRF P 4 HS2ICNRF P 4 Band HSM2HOST8 HS2LCDRF P 8 HS2IC Band HSM2HOST9 HS2LCDRF P 9 HS2IC PG9920 Only devices operating in band 912 919MHz are UL ULC Notes models PG9920 operating in the frequency band 912 are UL ULC listed The PG9920 has been listed by UL commercial burglary and residential fire burglary applications by ULC for residential burglary applications in accordance the requirements in the Standards UL1610 UL1023 UL985 ULC S545 UL ULC installations use these device only in conjunction compatible DSC wireless receivers HSM2HOST9 HS2LC HS2ICNRF P 9 and PG9920 After installation verify product functionality in conjunction with the compatible used The PG4920 and PG8920 are compliant with RTTE requirements Directive 1999 5 EC of the Parliament and of the Council of 9 March The PG8920 is certified by DNV DET VERITAS to the following standards EN50131 3 EN50131 1 GRADE 2 CLASS II EN50131 6 A DNV DET NORSKE VERITAS has certified only the MHz variant of this product According to EN 50131 1 2006 A1 2009 this equipment can be applied in installed systems up and including Security Grade 2 Environmental Class II UK PG8920 is suitable for use in systems installed to conform to at Grade 2 and environmental class 2 BS8243 COMPLIANCE STATEMENT Changes or modifications to this unit not expressly by the party responsible for compliance could void the authority to operate the equipment device has been tested and found to comply with the limits for Class B digital device pursuant to Part 15 of the FCC Rules limits are designed to provide reasonable protection against interference in residential installations This equipment uses and can radiate radio frequency energy and if not and used in accordance with the instructions may cause interference to radio and television reception there is no guarantee that interference will not occur in a installation If this device does cause such interference can be verified by turning the device off and on the user is to eliminate the interference by one or more of the fol measures Re orient or re locate the receiving antenna Increase the distance between the device and the receiver Connect the device to an outlet on a circuit different from the one supplies power to the receiver Consult the dealer or an experienced radio TV technician equipment complies with FCC and IC RF radiation exposure set forth for an uncontrolled environment device complies with FCC Rules Part 15 and with Industry licence exempt RSS standard s Operation is subject to following two conditions 1 This device may not cause harm interference and 2 this device must accept any interference may be received or that may cause undesired operation present appareil est conforme aux CNR d Canada aux appareils radio exempts de licence L autorisee aux deux conditions suivantes 1 l ne doit produire de brouillage et 2 l de l doit tout brouillage radioelectrique subi meme si le brouillage susceptible d compromettre le fonctionnement d du r fil PowerG r sans fil PowerG Series relaye les informations entre les dispositifs de commande sans fil PowerG et centrale PowerG Les r la port sans fil du en relayant les transmissions aux dispositifs qui seraient hors de la port de la centrale de service messages de service suivant peuvent transmis par le r au syst Batterie faible Supervision Panne d secteur Sabotage du dispositif L fournira l final les instruc Fin de vie concernant les mesur