DSC PG9945 - PG8945 - PG4945 - Installation Guide - EN - FR - ES - PT

File Preview
File Preview
Click below to download for free

Text Preview

Note After restoring a low battery trouble the system may take to 5 minutes to clear the trouble the Device into the System to the PowerSeries Neo Host Installation Manual or iotega Manual for the enrollment procedure Testing permanently mounting any wireless device temporarily the device and perform a Placement test the device by removing the cover Replace the cover to restore the tamper The device now Placement test mode for 15 minutes the device by opening the door or window and verify the LED blinks indicating detection After 2 seconds the LED blinks 3 times The following table received signal strength Strength communication response LED blinks LED blinks LED blinks blinks Only GOOD or STRONG signal strengths are If you receive a POOR signal from the device re locate and re test until a GOOD or STRONG signal is received For UL ULC installations only STRONG signal levels are After installation verify the product functionality in with HSM2HOST9 HS2ICNRF P 9 PG9920 WS900 19 and and Qolsys IQPanel2 For detailed Placement instructions refer to the control panel Guide Separation compatible of of Magnet Y X Z Ferrous Materials mm 5 mm 5 mm 5 mm 5 mm 5 mm 5 mm 5 mm 5 mm 5 mm 5 mm 5 mm 5 maximum gap separation for installation on speci materials and axes of use is 6mm 0.24 the Device is highly recommended to attach the transmitter to the top of the on the fixed frame and the magnet to the door or Ensure that the magnet is located not more than 6 mm in from the transmitter marked side Once the cover is removed a tamper message is transmitted the receiver Subsequent removal of the battery prevents of tamper restore leaving the receiver in permanent To avoid press the tamper switch while removing the battery unit has an optional back tamper switch under the PCB As as the PCB is seated firmly within the base the switch lever be pressed against a special break away base segment that is connected to the base Be sure to fasten the break away to the wall If the detector unit is forcibly removed from wall this segment will break away from the base causing the switch to open For UL and ULC Residential Fire and Commercial Burglary the use of the back tamper is mandatory Adhesive tape not to be used for EU Market with screws For UL and ULC Residential Fire and Commercial Burglary the use of the mounting screws is mandatory With the cover removed flex retainer and remove PCB Mark drill 2 holes in mounting surface Mount the magnet base with 2 supplied screws Attach the magnet to the magnet base with adhesive tape away the release liners from the two strips of double adhesive tape and attach to the device and magnet base with 2 countersunk screws Align the device with the magnet according to the location and fasten the device and magnet to the mounting sur Input wiring Connect the auxiliary sensor contacts across the auxiliary terminals the auxiliary input is defined as a Normally Closed N C series connected N C sensor contacts must be used An E O L resistor will not be required the auxiliary input of the is defined as a Normally Open type parallel connected N O sensor contacts must be exclusively An E O L resistor will not be required E O L supervision Normally Closed N C sensor con can be used A 47 k E O L resistor must be wired at far end of the zone loop For UL installations the device connected to the initiating must be located in the same room as the transmitter drawing below illustrates a N O and N C alarm circuit with resistor An alarm message is transmitted once the loop is opened or circuited For UL ULC installations connect only UL ULC listed to the auxiliary wiring input Only one device shall be to the input of each RF transmitter Receivers device can be used with DSC panels and receivers that use technology Notes PG9945 has been listed by UL and ULC for commercial and burglary and residential fire applications in accordance the requirements in the Standards UL 985 and ULC S545 fire applications and UL634 and ULC ORDC634 for Door Window Contact For UL and ULC installations use this only in conjunction with compatible DSC wireless HSM2HOST9 HS2LCDRF P 9 HS2ICNRF P 9 WS900 19 WS900 29 and Qolsys IQPanel2 Le remplacement des batteries doit r par un Pour garantir le fonctionnement continu de tous les sans fil apr avoir r une r aux par d un t g de toute la sans fil par DLS est recommand avant de le syst Apr avoir compl la r aux par d du syst t la programmation sans be enabled and ULC Residential Fire RF transmitter PG9945 is also UL985 and ULC S545 listed as a short RF transmitter for use in Residential fire applications in with UL and ULC listed mechanical heat detectors transmitter shall be installed using provided screws and the tamper shall be enabled The heat detector shall be connected the wired input of the RF transmitter device in the same room within 3 ft The External Input 001 03 shall be set to Y and Zone EOL 002 shall be set to 02 Normally Open The and Reed operation shall be disabled N When enrolling device in the compatible receiver control panel combination set zone definition to type 08 in order to transmit a fire alarm the external input is activated An example of compatible devices that could be used in this type of application is System Sensor UL and ULC listed 5600 Series Mechanical Detectors only models that have self restoring rate of rise Refer to the compatible devices installation testing and instructions Test the self restoring rate of rise models a hair dryer or heat gun When testing the ROR element to the activation of the fixed temperature element the heat must not exceed the fixed temperature rating of the detector shall be installed as per NFPA72 and ULC S540 and or local authority having jurisdiction Ensure RF conditions enter the wireless configuration section enter 804 3 digit number Alarm LED used Y Reed Switch Y External Input N Supervision Y the devices LED activate when an alarm occurs the reed Note It shall be set N for UL and ULC fire the exter input Note It shall be to Y for UL and ULC applications supervision of the Note It shall be set Y for UL and ULC fire EOL Default 01 auxiliary input as one of the following options Disabled Single EOL Normally Note it be set for UL ULC fire Normally Closed Band MHz CE Listed PG4945 433MHz CE EN PG8945 868MHz FCC IC UL ULC listed PG9945 912 band Protocol PowerG Input One internal Signaling at 4 minute intervals Alert Reported when a tamper event occurs type 3 V Lithium CR 123A type battery GP Life Expectancy 8 years for typical use Supervision Automatic transmission of battery condition as part of periodic status report and immediately upon low condition detection range 10 to 55 UL ULC only verified the 0 Humidity up to max 93 RH non condensing LxWxD 81 x 34 x 25 mm 3 3 16 x 1 1 4 x 1 in including battery 5

Related Files