DSC PG9984-PG8984-PG4984 - Installation Manual - ENG - FRE - SPA - POR - R002

D 304673 On the indicated location lift the screw cover upward using Wireless Dual Technology Mirror Motion Detector Installation PG9984 P PG8984 P PG4984 P are 2 way wireless Pet immune motion detectors utilizing Target Specific to distinguish between human beings and pets up to 18 kg 40lb while reduces false alarms by using Motion Recognition Built in link quality indicators installation time by eliminating the need for the installer physically approach the control panel The detectors also combined Fresnel and cylindrical optics that reach up to meters 49 ft and are equipped with wall creep zone protec Pet immunity feature has not been evaluated to UL 639 ULC S306 03 due to the feature not being addressed in standard Setup To be installed by service persons in indoor non haz locations only Risk of explosion if battery is replaced an incorrect type Observe polarity when installing batteries of used batteries according to the manufacturer and according to local rules and regulations Bat are to be replaced by service persons only To ensure the continued operation of all wireless devices performing a system default a global upload of all wire programming via DLS is recommended before defaulting system After completing the system default download the programming Screw Cover LED PIR Optical window Enroll button use a screwdriver to press the recessed but Battery Tamper switch Horizontal view of coverage area Vertical view of coverage area Microwave coverage Back tamper switch is required for UL commercial bur installations the battery Restore the The now mode 15 min Trip the thumb the arrow Loosen the screw and open the cover in the direction shown Insert a screwdriver into the slot shown and then push down to separate the base from the cover Insert battery while observing polarity When manually programming wireless devices if a has been powered up for more than 48 hours it cannot be into the system until the device has been tampered and When programming the panel using the Quick Enroll follow the steps detailed in Enroll the Device into the After restoring a low battery trouble the system may take to 5 minutes to clear the trouble the Device into the System quick enroll On a keypad press 8 Installer Code 804 000 Press and hold the device enroll button until the LED lights and then release the enroll button while the LED is lit A confirmation message then appears on the keypad Press key to confirm ID Enter 3 digit zone Enter 3 digit zone type Enter 1 digit partition for all desired partitions and press If using a menu based configuration you can scroll to the partitions and press to toggle the partition On an LCD keypad enter the label by using word library pre enroll Remotely configure the unique ID number into the system more information see the HS2MHOST manual When on site press the device enroll button If the wireless device has been powered for more then 48 without being enrolled tamper and restore the device to it a placement test Perform walktest at least once a year permanently mounting any wireless device temporarily the device and perform a Placement test Tamper the by the PowerG Series wireless PIR Motion detectors shall be and used within an environment that provides the pol degree max 2 and overvoltages category II Keep away from heat sources Do not expose to air drafts Do not install outdoors Avoid direct sunshine Keep wiring away from power cables Do not install behind partitions Mount on solid stable surface Notes Do not obscure the detector field of view large objects such as furniture Install in position such that intruder motion is perpendicular to the zones of detec Mount further than 5ft from fluorescent light fixture two fluorescent tubes minimum rated 40 W The PGx984 detector is immune to activity below m 3ft from 38 kg 85 lb animals Above the 1 m 3 ft limit the detector is immune to 19 kg 42 lb animals immunity decreases as the animal gets closer to the detec Select a mounting location that minimizes potential close of animals Pet immunity feature has not been verified by UL ULC To comply with FCC and IC RF exposure compli requirements the PIR detector should be located at a dis of at least 20 cm from all persons during normal The antennas used for this product must not be co or operated in conjunction with any other antenna or Mount the Device your mounting height and desired detector range the table below determine if you are to use mounting x or y Mounting flat or in a corner requires using different holes Mount using the supplied screws Holes 3.0m 15m enter the wireless configuration section enter 804 Zone Toggles Alarm LED Default Y the devices LED to activate when an alarm occurs Supervision Default Y supervision of the device Hightraffic Shutdown Default 01 and red LED once identify a signal being sent to the receiver and then blinks three times to the signal strength To perform a walk test walk the far end of coverage pattern in both directions following table indicates received signal strength indi Strength response LED blinks LED blinks GOOD LED blinks blinks communication Only GOOD or STRONG signal strengths are If you receive a POOR signal from the device re it and re test until a GOOD or STRONG signal is For UL ULC installations only STRONG signal levels acceptable After installation verify the product functional in conjunction with the compatible receivers HSM2HOST9 HS2ICNRF P 9 and PG9920 For detailed placement instructions refer to the control Reference Guide the Device this feature helps conserve battery power the system is disarmed by configuring a reporting When motion is detected the device transmits an to the receiver and will not report any further until the timer expires Any motion detected the configured period will be reported once the expires No Delay causes the device to report an each time the detector is tripped Detector Dis while dis 15 second 5m delay 60m delay 30 second 10m delay 5 second 20m delay No Delay 1m delay Event counter Default 002 activates after a configured number of events been detected in activities Operation Indications LED blinks LED on 0.2 sec LED blinks twice LED on 2 sec LED on warm up 60 open close quad PIR detection in mode alarm detection Testing detection Normal LED blinks slowly 0.2 ON 30 sec OFF Type Dual element low noise pyroelectric sensor Data of Beam Elements 18x3 54 far parabolic mirror seg of Curtain Elements 18 Coverage 15 m 49 ft 90 10 m 33 ft 90 5 m 16 ft 90 For UL ULC listed installations the following settings required coverage Maximum counter High Sensitivity Immunity PGx984P Up to 18 kg 40 lb Type K Band Doppler module 24 GHz Battery 3V Lithium battery type CR 123A con grade UL or equivalent listed RoHS compliant Dispose used batteries according to local regulations For UL installations use Panasonic Sanyo GP or Varta Battery Capacity 1450 mA h Life for typical use minimum one year typical 5 8 not verified by UL ULC Battery Threshold 2.5 V Motion Event Verification 2 remote selections 1 or 2 ON motion events Alarm Period 2 seconds Band MHz CE Listed PG4984 433MHz CE listed PG8984 868MHz FCC IC UL ULC listed PG9984 MHz Protocol PowerG Signaling at