DSC Power864 - Assign keypads to partitions 864 rev 005

Assigning a Keypad to a Partition Power864 connected to the PC5020 panel can be assigned one of nine ways a keypad can be to operate a partition from 1 to 8 or as a global keypad Global keypads will not display information except for a trouble condition if present until the keypad is temporarily assigned either a partition from 1 to 8 A global keypad allows the user to operate eight partitions the use of one keypad keypad partition assignment is a two step process Enable Partitions Assign the Keypad to a Partition and Slot Keypad Supervision Sections 201 000 0 902 1 to 8 Enable Assignment Supervision Field 1 Partition 2 8 Enable 2 through 8 must be enabled before keypads assigned to a partition 2 8 will operate enable partition 2 to 8 perform the following 8 Installer Code 201 2 to turn ON option 2 3 to turn ON option 3 4 to turn ON option 4 5 to turn ON option 5 6 to turn ON option 6 7 to turn ON option 7 8 to turn ON option 8 Installer Programming Partition 1 to 8 Enable Partition 2 Partition 3 Partition 4 Partition 5 Partition 6 Partition 7 Partition 8 2 Keypad Assignment the Partition Assignment and Slot of each keypad To assign the keypad perform the Installer Programming Keypad Assignment Section Partition and Slot Section 8 Installer Code 000 0 a two digit number The first number represents the partition assigned to the keypad data 0 data 1 data 2 data 3 data 4 data 5 data 6 data 7 data 8 Global Mode Partition 1 Partition 2 Partition 3 Partition 4 Partition 5 Partition 6 Partition 7 Partition 8 second digit represents the supervisory slot data 1 to 8 supervisory slot 1 to 8 same procedure must be performed on each keypad Keypads must each be assigned to a specific slot for the keypads to be properly an LCD5500Z keypad is connected to the panel it must be assigned to slot 8 for purposes In addition only one LCD5500 Z can be assigned to Slot If LCD programming changes are made using the DLS software the keypad to slot 8 will transmit the changes to all the other LCD5500Z keypads on system after the download is complete 2 Module Supervisory Reset all modules are automatically detected and supervised by the panel within the first minute being connected a Module Supervisory trouble condition may occur after keypad slot are changed After all keypads have been assigned to a Partition and Slot perform following to perform a Module Supervisory Reset Installer Programming Module Supervision Reset Installer Programming 8 Installer Code 902 1 minute verify what modules are present perform the following keypad will display the modules present LED keypads will be limited to the number of modules it can display To determine Installer Programming Module Supervision Display 8 Installer Code 903 LED represents which module refer to the Installation Manual Section 2.7 Tips a keypad is assigned to partition 2 to 8 and the partition is not enabled the keypad will function To correct the issue press and hold the key for 3 seconds then press hold 1 to temporarily assign the keypad to partition 1 Enter Installer Programming enable partition 2 to 8 Step 1 above To temporarily assign a global keypad to a partition press and hold the partition number 3 seconds For example press and hold 1 for partition 1 or 2 for partition 2 etc If key is pressed for 20 seconds the keypad will return to the global state A partition keypad can be temporarily assigned to another partition To do this press and the key for 3 seconds The keypad will beep three times Press and hold the number for 3 seconds For example press and hold 1 for partition 1 or 2 for 2 etc If no key is pressed for 20 seconds the keypad will return to the partition was originally assigned to When accessing Partition 3 through 8 an LCD5501 keypad or an LCD5500 Z v3.0 must be used Test a zone assigned to Partition 2 and ensure it is displayed on a partition 2 keypad