DSC PS3020 Power Supply Installation Instructions

PS3020 Supply N S T A L L A T I O N I N S T R U C T I O N S PS3020 is a 2.2 amp regulated power supply with a built in battery charging and AC power indicator The board is 8.4cm 3.3 x 6.6cm 2.6 and comes adhesive foam mounting tape DO NOT exceed the maximum recommended current Risk of fire if it over 2.2A 6 volt or 12 volt operation jumper selectable Provides correct charging voltage for rechargeable gel cell batteries adjustable for lead acid batteries AC power on LED indicator Automatic switch over to standby battery power in case of AC power failure Output is fused at 5 amps for higher battery assisted output current Instructions the time of installation select proper operating voltage For 6 volt operation leave yellow jumper intact For 12 volt operation cut yellow jumper AC power only without battery con measure DC voltage and load current the measured or estimated load current can obtain your transformer and battery the battery and remove AC power circuit should operate normally the AC power your circuit is now tested and functional This power supply is not to be used in UL ULC listed installations Requirements For maximum power 6 VDC 12 volts 80 VA 12 VDC 16 volts 80 VA OUT MAX 5 AMP WARRANTY Security Controls warrants that for a period of twelve 12 months from the date of purchase by the buyer the product shall be free of defects in materials and workmanship under normal use and that of any breach of such warranty Digital Security Controls shall at its option repair or replace the equipment upon return of the equipment to its factory This warranty applies only to defects in parts workmanship and not to damage incurred in shipping or handling or damage due to causes beyond the control Digital Security Controls such as lightning excessive voltage mechanical shock water damage or damage out of abuse alteration or improper application of the equipment foregoing warranty shall apply only to the original buyer and is and shall be in lieu of any and all other whether expressed or implied and of all other obligations or liabilities on the part of Digital Controls This warranty contains the entire warranty Digital Security Controls neither assumes nor any other person purporting to act on its behalf to modify or change this warranty or liability concerning product no event shall Digital Security Controls be liable for any direct indirect or consequential damages loss of profits loss of time or any other losses incurred by the buyer in connection with the purchase or operation or failure of this product Digital Security Controls recommends that the entire system be tested on a regular basis despite frequent testing and due to but not limited to criminal tampering or electrical it is possible for this product to fail to perform as expected Supply N S T A L L A T I O N I N S T R U C T I O N S PS3020 is a 2.2 amp regulated power supply with a built in battery charging and AC power indicator The board is 8.4cm 3.3 x 6.6cm 2.6 and comes adhesive foam mounting tape DO NOT exceed the maximum recommended current Risk of fire if it over 2.2A 6 volt or 12 volt operation jumper selectable Provides correct charging voltage for rechargeable gel cell batteries adjustable for lead acid batteries AC power on LED indicator Automatic switch over to standby battery power in case of AC power failure Output is fused at 5 amps for higher battery assisted output current Instructions the time of installation select proper operating voltage For 6 volt operation leave yellow jumper intact For 12 volt operation cut yellow jumper AC power only without battery con measure DC voltage and load current the measured or estimated load current can obtain your transformer and battery the battery and remove AC power circuit should operate normally the AC power your circuit is now tested and functional This power supply is not to be used in UL ULC listed installations Requirements For maximum power 6 VDC 12 volts 80 VA 12 VDC 16 volts 80 VA OUT MAX 5 AMP WARRANTY Security Controls warrants that for a period of twelve 12 months from the date of purchase by the buyer the product shall be free of defects in materials and workmanship under normal use and that of any breach of such warranty Digital Security Controls shall at its option repair or replace the equipment upon return of the equipment to its factory This warranty applies only to defects in parts workmanship and not to damage incurred in shipping or handling or damage due to causes beyond the control Digital Security Controls such as lightning excessive voltage mechanical shock water damage or damage out of abuse alteration or improper application of the equipment foregoing warranty shall apply only to the original buyer and is and shall be in lieu of any and all other whether expressed or implied and of all other obligations or liabilities on the part of Digital Controls This warranty contains the entire warranty Digital Security Controls neither assumes nor any other person purporting to act on its behalf to modify or change this warranty or liability concerning product no event shall Digital Security Controls be liable for any direct indirect or consequential damages loss of profits loss of time or any other losses incurred by the buyer in connection with the purchase or operation or failure of this product Digital Security Controls recommends that the entire system be tested on a regular basis despite frequent testing and due to but not limited to criminal tampering or electrical it is possible for this product to fail to perform as expected Digital Security Controls Canada cid 129 www dsc com Support Canada US or 905 760 3036 in Canada Digital Security Controls Canada cid 129 www dsc com Support Canada US or 905 760 3036 in Canada