DSC PTD1610-SCW Install Manual - English

PTD1610 SCW Installation Instructions for use with DSC SCW9045 or DSC SCW9047 alarm systems following are the contents of this box see Diagram 1 included plastic housing plastic housing cover to 16.5V 10VA transformer block with fuse mounted 230VAC warning sticker and marking label 4 mounting screws 1 screw to secure cover plastic housing away tabs 1 hole primary of the transformer red wires is rated at 50Hz 60Hz 70mA The secondary of the transformer yellow wires is rated at 16.5VAC 10VA Block fuse block is used to connect the incoming AC to the primary of the transformer with a SB Slow Blow 250V fuse in between to protect the transformer wiring can be brought into the plastic cabinet in one of 3 ways the wire access holes in the back of the plastic housing flush mount wiring break away one of the four tabs located along the outer edge of the housing see Diagram 1 drilled holes in the sides of the cabinet On all sides of the bottom plastic housing one there are dots in the plastic which are used to indicate drill hole locations see 1 The drill holes are marked to prevent accidental drilling into the transformer primary of the transformer red wires are connected to one side of the fuse block The incom 230VAC is to be connected to the opposite side of the fuse block see Diagram 2 secondary of the transformer yellow wires is to connected to the AC terminals of the control with which the transformer is used 2 VAC AC the four screws provided mount the bottom housing to the intended mounting surface its 4 foot holes the cover plastic housing onto the plastic housing and secure the connection using the screw The equipment must be secured to the building before operation It is designed be mounted INDOOR NON HAZARDOUS LOCATIONS ONLY The end user shall be not to open the enclosure of the power supply as it presents the risk of an shock hazard The connection to the mains supply must be made as per the local authorities rules and regu in the UK as per BS6701 A readily accessible disconnect device shall be incorporated to the equipment that shall disconnect both poles simultaneously to disconnect the for servicing wires a knockout tab is removed during the installation it is the installer responsibility to ensure the same degree of protection for the cabinet is provided by the use of bushings fittings The enclosure must be secured to the building structure before operation The equipment is intended to be installed by SERVICE PERSONS ONLY or equivalent i e having appropriate technical training and the experience necessary to be aware of to which they may be exposed to in performing that task and of the measures to the risks to themselves and other persons wiring must be routed in a manner prevents 3 Non Combustible Material Housing Block Transformer excessive strain on wire and on terminal loosening of terminal connections damage of conductor insulation The power supply must be CONNECTED The transformer box must be mounted ver on a wall made from non combusti materials only see Diagram 3 the mains supply remains below 215Vac an extended period of time the battery will not charge Warranty Security Controls warrants that for a period of twelve months from the date of purchase the product shall be free of in materials and workmanship under normal use and that in fulfilment of any breach of such warranty Digital Security shall at its option repair or replace the defective equipment upon return of the equipment to its factory This warranty only to defects in parts and workmanship and not to damage incurred in shipping or handling or damage due to causes the control of Digital Security Controls such as lightning excessive voltage mechanical shock water damage or arising out of abuse alteration or improper application of the equipment foregoing warranty shall apply only to the original buyer and is and shall be in lieu of any and all other warranties whether or implied and of all other obligations or liabilities on the part of Digital Security Controls This warranty contains entire warranty Digital Security Controls neither assumes responsibility for nor authorizes any other person purporting to on its behalf to modify or to change this warranty nor to assume for it any other warranty or liability concerning this product no event shall Digital Security Controls be liable for any direct or indirect or consequential damages loss of anticipated loss of time or any other losses incurred by the buyer in connection with the purchase installation or operation or failure this product Digital Security Controls recommends that the entire system be completely tested on a regular basis despite frequent testing and due to but not limited to criminal tampering or electrical disruption it is for this product to fail to perform as expected Digital Security Controls Canada www dsc com Support 1 800 387 3630 Can US 905 760 3036 Intl in China Installation Instructions for use with DSC SCW9045 or DSC SCW9047 alarm systems following are the contents of this box see Diagram 1 included plastic housing plastic housing cover to 16.5V 10VA transformer block with fuse mounted 230VAC warning sticker and marking label 4 mounting screws 1 screw to secure cover plastic housing away tabs 1 hole primary of the transformer red wires is rated at 50Hz 60Hz 70mA The secondary of the transformer yellow wires is rated at 16.5VAC 10VA Block fuse block is used to connect the incoming AC to the primary of the transformer with a SB Slow Blow 250V fuse in between to protect the transformer wiring can be brought into the plastic cabinet in one of 3 ways the wire access holes in the back of the plastic housing flush mount wiring break away one of the four tabs located along the outer edge of the housing see Diagram 1 drilled holes in the sides of the cabinet On all sides of the bottom plastic housing one there are dots in the plastic which are used to indicate drill hole locations see 1 The drill holes are marked to prevent accidental drilling into the transformer primary of the transformer red wires are connected to one side of the fuse block The incom 230VAC is to be connected to the opposite side of the fuse block see Diagram 2 secondary of the transformer yellow wires is to connected to the AC terminals of the control with which the transformer is used 2 VAC AC the four screws provided mount the bottom housing to the intended mounting surface its 4 foot holes the cover plastic housing onto the plastic housing and secure the connection using the screw The equipment must be secured to the building before operation It is designed be mounted INDOOR NON HAZARDOUS LOCATIONS ONLY The end user shall be not to open the enclosure of the power supply as it presents the risk of an shock hazard The connection to the mains supply must be made as per the local authorities rules and regu in the UK as per BS6701 A readily accessible disconnect device shall be incorporated to the equipment that shall disconnect both poles simultaneously to disconnect the for servicing wires a knockout tab is removed during the installation it is the installer responsibility to ensure the same degree of protection for the cabinet is provided by the use of bushings fittings The enclosure must be secured to the building structure before operation The equipment is intended to be installed by SERVICE PERSONS ONLY or equivalent i e having appropriate technical training and the experience necessary to be aware of to which they may be exposed to in performing that task and of the measures to the risks to themselves and other persons wiring must be routed in a manner prevents 3 Non Combustible Material Housing Block Transformer excessive strain on wire and on terminal loosening of terminal connections damage of conductor insulation The power supply must be CONNECTED The transformer box must be