DSC RFK5516 Installation Manual (Polish, Czech, Chinese, English)

v1.2 Instructions Instrukcja instalacji Instala pokyny Polski Please refer to the System Installation Manual for information on limitations regarding product use and function and information on the limitations as to liability of the manufacturer These instructions shall be used in conjunction with the system Installation Manual of the Control Panel with which this equipment is intended to be used Informacje dotycz ogranicze u i funkcji produktu oraz informacje dotycz ogranicze odpowiedzialno producenta podano w podr instalacji systemu Instrukcje zawarte w tej publikacji nale stosowa z instrukcjami zawartymi w podr instalacji panelu sterowania z kt ten produkt ma by u Omezen t se pou a fungov v a informace o omezen v souvislosti s ru v najdete v p pro instalaci syst Tyto pokyny se pou spole s p pro instalaci panelu s n se m toto za pou Instructions PK55XX keypads can be used on security systems with to 64 zones These keypads are compatible with the latest version the folllowing DSC security systems RFK55XX keypads combine a wireless receiver with the respective keypad Temperature range 10 to 55 14 to 131 Temperature for UL ULC 0 to 49 32 to 120 Humidity MAX 93 R H Plastic enclosure protection degree IP30 IK04 Voltage rating 12VDC nominal Connects to control panel via 4 wire Keybus 1 keypad zone input PGM output PK55XX Current draw 50mA standby 125mA maximum RFK55XX Current draw 75mA standby 135mA maximum Wall mount tamper 5 programmable function keys Ready Green LED Armed Red LED Trouble Yellow LED AC LED Low temperature sensor Frequency 433.92MHz RFK55XX 433 868MHz RFK55XX 868 Up to 32 wireless zones RFK55XX Only Zone not to be programmed as Fire type or 24h type Power keypad package includes the following parts Power keypad mounting screws end of line resistors should mount the keypad where it is accessible to designated of entry and exit Once you have selected a dry and secure loca perform the following steps to mount the keypad inner door labels tamper switch Instructions Keypad Insert a flat head screwdriver into the provided slot first of two Move screwdriver toward the back plastic and lift as in the below This will unhook one side of the front plastic Repeat step 1 and 2 on the second provided slot to disconnect front plastic and allow access for wiring engage and Wire Keypad Out Slot Out Out to Snap Secure Keypad to wall using mounting holes Use all 4 screws provided mounting on a single gang box Place keypad into hooks on the backplate and swing down to engage Run wire through wiring slot or knockouts Connect Keybus and PGM Zone to keypad Place tamper switch into tamper hole on backplate Remove keypad from hooks Place keypad into backplate ensure the wire pushed back into the wall as much as possible Route the wire inside keypad ensuring high components are avoided Snap the front assem closed ensuring that there is no pressure to the keypad from the wire If any tension found between the front keypad assembly and wiring open the keypad reroute the wire and close again Repeat these until the keypad is closed properly Before wiring the unit ensure that all power AC transformer and battery disconnected from the control panel Connect the four Keybus wires from the con panel red black yellow and green to keypad terminals Refer to diagram zone or output If programmed as an input you can con a device such as a door contact to terminal of the keypad This elim the need to run wires back to the panel for the device To connect the run one wire from the device to the terminal and the other wire the device to the B black terminal For powered devices run the red to the R positive terminal and the black wire to the B negative When using end of line supervision connect the zone according one of the configurations outlined in your system Installation Manual If the terminal is programmed as an output the output follows the programmed in Section 080 A small relay buzzer or other DC device may be connected between the positive supply voltage the terminal maximum load is 50mA Option 4 For UL Residential Fire Installations use at least one addi DSC compatible keypad in conjunction with an RFK55XX or install the RFK55XX keypads within 3 feet from the con unit and mechanically protect the keybus wires Power all wiring is complete and the equipment is secured to the building with at least two screws apply power to the control panel Connect the battery leads to the battery Connect the AC transformer more information on control panel power specifications see the control Installation Manual the Keypad are several programming available for the keypad are described below Pro the keypad is similar programming the rest of the When you are in the key programming sections the will display which are turned on along the of the display To turn an on or off press the num corresponding to the option the number pad The numbers of the options that are currently turned will be displayed For example if options 1 and 4 are on the display look like this on the different keypad displays information on programming the rest of your security system please to your system Installation Manual LCD Labels LCD programming is done per keypad If more than one LCD keypad is on the system labels programmed at one keypad can be broadcast all other LCD keypads Perform the following procedure in order to broad labels 1 Program one LCD keypad completely 2 Make sure all LCD keypads are connected to the Keybus 3 Enter keypad programming by pressing 8 Installer Code enter section 998 at the keypad that was programmed The keypad now broadcast all the information programmed to all the other LCD key on the system 4 When the keypad is finished press the key to exit LCD Label broadcast from this keypad is only compatible PC1616 1832 1864 control panels and other PK5500 keypads Programming Only keys for 2 seconds to enter language programming scroll to desired language and Press to select If section 077 option 4 is OFF language programming o