DSC RM-2 Relay Module

Mounting of the Relay in an Electrical Box Relay Module Smoke Detector Detector Plate Supervision RM 2 Box deep WARRANTY Security Controls Ltd warrants that for a period of twelve months from the date of purchase the shall be free of defect in materials and workmanship under normal use and that in fulfilment of breach of such warranty Digital Security Controls Ltd shall at its option repair or replace the defective upon return of the equipment to its repair depot This warranty applies only to defects in parts workmanship and not to damage incurred in shipping or handling or damage due to causes beyond control of Digital Security Controls Ltd such as lightning excessive voltage mechanical shock water or damage arising out of abuse alteration or improper application of the equipment foregoing warranty shall apply only to the original buyer and is and shall be in lieu of any and all other whether expressed or implied and of all other obligations or liabilities on the part of Digital Se Controls Ltd This warranty contains the entire warranty Digital Security Controls Ltd neither as nor authorizes any other person purporting to act on its behalf to modify or to change this nor to assume for it any other warranty or liability concerning this product no event shall Digital Security Controls Ltd be liable for any direct indirect or consequential damages of anticipated profits loss of time or any other losses incurred by the buyer in connection with the installation or operation or failure of this product Digital Security Controls Ltd recommends that the entire system be completely tested on a reg basis However despite frequent testing and due to but not limited to criminal tampering or electri disruption it is possible for this product to fail to perform as expected Digital Security Controls Ltd Canada cid 127 www dsc com in Canada all comments concerning this publication to pubs dscltd com Instructions RM 2 Relay Module is used as an end of line EOL power supervision module for smoke detectors The RM 2 is used with the Polarity Reversal Module PRM and DSC FSA 410 series smoke detectors the PRM 4W reverses polarity on the smoke detector loop to activate all smoke sounders the RM 2 Relay will continue to operate normally regardless of power polarity Refer to the PRM 2W 4W Polarity Reversal Module Installation Specifications Voltage Range 10VDC to 30VDC Contact Rating 2A 30VDC VAC Rating 25mA Environment 0 49 32 120 93 RH non condensing H x W x D 28.5 x 86 x 21mm 1 1 8 x 3 3 8 x 7 8 in Wire Gauge 14 22 AWG Diagram the connection wires through the wiring holes on the back of the unit mount the unit remove the plastic cover and secure the unit to the desired loca with the screws provided Replace the cover module can also be mounted inside a standard 4 electrical box 1.5 deep if by the installation Please refer to the diagrams below SMOKE DETECTORS Reversal Module Series Smoke Detector Panel P C Com VDC EOLR RM 2 Relay Mounting of the Relay in an Electrical Box Relay Module Smoke Detector Detector Plate Supervision RM 2 Box deep WARRANTY Security Controls Ltd warrants that for a period of twelve months from the date of purchase the shall be free of defect in materials and workmanship under normal use and that in fulfilment of breach of such warranty Digital Security Controls Ltd shall at its option repair or replace the defective upon return of the equipment to its repair depot This warranty applies only to defects in parts workmanship and not to damage incurred in shipping or handling or damage due to causes beyond control of Digital Security Controls Ltd such as lightning excessive voltage mechanical shock water or damage arising out of abuse alteration or improper application of the equipment foregoing warranty shall apply only to the original buyer and is and shall be in lieu of any and all other whether expressed or implied and of all other obligations or liabilities on the part of Digital Se Controls Ltd This warranty contains the entire warranty Digital Security Controls Ltd neither as nor authorizes any other person purporting to act on its behalf to modify or to change this nor to assume for it any other warranty or liability concerning this product no event shall Digital Security Controls Ltd be liable for any direct indirect or consequential damages of anticipated profits loss of time or any other losses incurred by the buyer in connection with the installation or operation or failure of this product Digital Security Controls Ltd recommends that the entire system be completely tested on a reg basis However despite frequent testing and due to but not limited to criminal tampering or electri disruption it is possible for this product to fail to perform as expected Digital Security Controls Ltd Canada www dsc com in Canada all comments concerning this publication to pubs dscltd com Instructions RM 2 Relay Module is used as an end of line EOL power supervision module for smoke detectors The RM 2 is used with the Polarity Reversal Module PRM and DSC FSA 410 series smoke detectors the PRM 4W reverses polarity on the smoke detector loop to activate all smoke sounders the RM 2 Relay will continue to operate normally regardless of power polarity Refer to the PRM 2W 4W Polarity Reversal Module Installation Specifications Voltage Range 10VDC to 30VDC Contact Rating 2A 30VDC VAC Rating 25mA Environment 0 49 32 120 93 RH non condensing H x W x D 28.5 x 86 x 21mm 1 1 8 x 3 3 8 x 7 8 in Wire Gauge 14 22 AWG Diagram the connection wires through the wiring holes on the back of the unit mount the unit remove the plastic cover and secure the unit to the desired loca with the screws provided Replace the cover module can also be mounted inside a standard 4 electrical box 1.5 deep if by the installation Please refer to the diagrams below SMOKE DETECTORS Reversal Module Series Smoke Detector Panel P C Com VDC EOLR RM 2 Relay