DSC SCW9045 47 UM EN

Self Contained Wireless Alarm System v1.0 Guide This manual contains information on limitations regarding product use and and information on the limitations as to liability of the manufacturer entire manual should be carefully read COMPLIANCE STATEMENT Changes or modifications not expressly approved by Dig Security Controls could void your authority to use this equipment equipment has been tested and found to comply with the limits for a B digital device pursuant to Part 15 of the FCC Rules These limits designed to provide reasonable protection against harmful interfer in a residential installation This equipment generates uses and can radio frequency energy and if not installed and used in accord with the instructions may cause harmful interference to radio com However there is no guarantee that interference will not in a particular installation If this equipment does cause harmful in to radio or television reception which can be deter mined by the equipment off and on the user is encouraged to try to correct interference by one or more of the following measures Re orient the receiving antenna Connect the equipment into an outlet on a circuit different from that the separation between the equipment and receiver which the receiver is connected Consult the dealer or an experienced radio television technician for user may find the following booklet prepared by the FCC useful to Identify and Resolve Radio Television Interference Problems booklet is available from the U S Government Printing Office D C 20402 Stock 004 000 00345 4 INFORMATION equipment complies with Part 68 of the FCC Rules and if the was approved July 23 2001 or later the requirements adopted the ACTA On the side of this equipment is a label that contains other information a product identifier If requested this number be provided to the Telephone Company Product Identifier USOC Jack Connection Requirements plug and jack used to connect this equipment to the premises wiring telephone network must comply with the applicable FCC Part 68 and requirements adopted by the ACTA A compliant telephone and modular plug is provided with this product It is designed to connected to a compatible modular jack that is also compliant See instructions for details Equivalence Number REN REN is used to determine the number of devices that may be con to a telephone line Excessive RENs on a telephone line may re in the devices not ringing in response to an incoming call In most not all areas the sum of RENs should not exceed five 5.0 To be of the number of devices that may be connected to a line as de by the total RENs contact the local Telephone Company For approved after July 23 2001 the REN for this product is part the product identifier that has the format US AAAEQ TXXXX digits represented by are the REN without a decimal point e g is a REN of 0.3 For earlier products the REN is separately shown the label REN 0.1B of Harm this equipment SCW9047 SCW9045 causes harm to the telephone the telephone company will notify you in advance that tempo discontinuance of service may be required But if advance notice is practical the Telephone Company will notify the customer as soon as Also you will be advised of your right to file a complaint with FCC if you believe it is necessary in Telephone Company Equipment or Facilities Telephone Company may make changes in its facilities equipment or procedures that could affect the operation of the equipment this happens the Telephone Company will provide advance notice in for you to make necessary modifications to maintain uninterrupted Maintenance Facility trouble is experienced with this equipment SCW9047 SCW9045 for or warranty information contact the facility indicated below If the is causing harm to the telephone network the Telephone may request that you disconnect the equipment until the prob is solved This equipment is of a type that is not intended to be re by the end user c o APL Logistics 757 Douglas Hill Rd Lithia Springs GA Information to party line service is subject to state tariffs Contact the state utility commission public service commission or corporation for information dialling equipment must be able to seize the telephone line and a call in an emergency situation It must be able to do this even if equipment telephone answering system computer modem etc has the telephone line in use To do so alarm dialling equipment be connected to a properly installed RJ 31X jack that is electrically series with and ahead of all other equipment attached to the same tele line Proper installation is depicted in the figure below If you have questions concerning these instructions you should consult your tel company or a qualified installer about installing the RJ 31X jack alarm dialling equipment for you Premises Equipment and Wiring Dialing Jack Machine Jack CANADA STATEMENT This product meets the applicable Industry Canada technical pr materiel est conforme aux specifications techniques applica d Canada Ringer Equivalence Number REN for this terminal equipment is 0.1 d de la sonnerie IES du pr mat est de 0.1 Ringer Equivalence Number is an indication of the maximum of devices allowed to be connected to a telephone interface termination on an interface may consist of any combination of de subject only to the requirement that the sum of the RENs of all the does not exceed five d de la sonnerie sert indiquer le nombre maximal de terminaux qui peuvent une interface t La terminaison d interface consister en une combinaison quelconque de dispositifs la seule que la somme d d de la sonnerie de tous dispositifs n pas 5 term before the radio certification number only signifies that Canada technical specifications were met Number IC 160A 9047 Class B digital apparatus complies with Canadian ICES 003 appareil num de la classe B est conforme la norme NMB du Canada Zealand The following is a list of warnings applicable when this equipment is connected to the New Zealand Telecom Network DSC SCW9047 433 System may be to the Telecom XXX XX XXX DSC SCW9045 433 System may be to the Telecom XXX XX XXX Warning grant of a Telepermit for any item of terminal equipment indicates only that Telecom has accepted that the complies with minimum conditions for connection to its network It indicates no endorsement of the product Telecom nor does it provide any sort of warranty Above all it provides no assurance that any item will work in all respects with another item of Telepermitted equipment of a different make or model nor does it that any product is compatible with all of Telecom s network services Numbering decadic signalling signalling should not be used as it is being progressively phased out of the network DTMF dialling is available and it should always be used Grabbing Equipment equipment is set up to carry out test calls at pre determined times Such test calls will interrupt any other that may be set up on the line at the same time The timing set for such test calls should be discussed with the timing set for test calls from this equipment may be subject to drift If this proves to be inconvenient and calls are interrupted then the problem of timing should be discussed with the equipment installer The mat should NOT be reported as a fault to Telecom Faults Service Line Feed to Other Devices dialling this device unit does not provide DC voltage to the series port connection and this may cause loss memory functions for the terminal devices local telephone connected to T 1 R 1 Operation ringer sensitivity and loading device only responds to Distinctive Alert cadences DA1 and DA2 of Contents Your Security System 1 Detection