DSC SCW9055-SCW9057 - V1 2 - Installation Manual - En

Self Contained Wireless Alarm System This manual contains information on limitations regarding product use and function information on the limitations as to liability of the manufacturer The entire manual should carefully read Installation Guide of Contents Introduction 1 SCW9055 57 Model Differences 1 Compatible Wireless Devices 1 Product Specifications 2 Controls Indicators 3 Data Entry 3 Installation 5 Mounting 5 Wiring 6 Wireless Device Setup 7 Alternate Communicator Module Setup Initialization 9 Operation 10 Operating Modes 10 Language Selection 10 Commands 10 Function Keys 13 System Removal Prevention 13 Programming 14 Template Programming 14 DLS Programming 17 Installer Programming 17 Advanced Programming 18 How to Program 18 Index to Programming Worksheets and Descriptions 19 Programming Worksheets 20 Programming Descriptions 42 Testing and Troubleshooting 72 A Reporting Code Formats 75 B 2 Way Audio Verification SCW9057 only 80 C Communicator Format Options 81 INSTRUCTIONS for SERVICE PERSONNEL When using equipment connected to the TELEPHONE NETWORK there are basic safety instructions that should always followed Refer to the SAFETY INTRUCTIONS provided with this product save them for future reference Instruct the end user the safety precautions that shall be observed when operating this equipment Installing The Equipment your package includes the following items and User Manuals including the SAFETY INSTRUCTIONS and SAVE These Instructions All WARNINGS AND INSTRUCTIONS specified within this document and or on the equipment alarm controller Supply direct plug in Mounting hardware A Suitable Location For The Alarm Controller the following list as a guide to find a suitable place for this equipment near a telephone socket and power outlet a place free from vibration and shocks the alarm controller on a flat stable surface and follow the installation Instructions NOT locate this product where persons may walk on the secondary circuit cable s NOT connect the alarm controller to electrical outlets on the same circuit as large appliances NOT select a place that exposes your alarm controller to direct sunlight excessive heat moisture vapors chemicals or dust NOT install this equipment near water e g bath tub wash bowl kitchen laundry sink wet basement near a swimming pool NOT install this equipment and its accessories in areas where there is a risk of explosion NOT connect this equipment to electrical outlets controlled by wall switches or automatic timers interference sources setting up the equipment near heaters air conditioners ventilators and or refrigerators locating this equipment close to or on top of large metal objects e g metal wall studs Precautions Required During Installation install this equipment and or telephone wiring during a lightning storm touch uninsulated telephone wires or terminals unless the telephone line has been disconnected at the network interface cables so that accidents can not occur Connected cables must NOT be subject to excessive mechanical strain only the power supply provided with this equipment Use of unauthorized power supplies may cause damage direct plug in versions use the transformer supplied with the device EQUIPMENT HAS NO MAINS ON OFF SWITCH THE PLUG OF THE DIRECT PLUG IN POWER SUPPLY IS TO SERVE AS THE DISCONNECTING DEVICE IF THE EQUIPMENT MUST BE QUICKLY DISCONNECTED IT IMPERATIVE THAT ACCESS TO THE MAINS PLUG AND ASSOCIATED MAINS SOCKET OUTLET IS NEVER NOTE Alarm System shall be installed and used within an that provides the pollution degree max 2 and over category II NON HAZARDOUS LOCATIONS indoor The equipment is DIRECT PLUG IN external transformer is designed to be installed serviced and or repaired by persons only service person is defined as a person the appropriate technical training and experience to be aware of hazards to which that person may be in performing a task and of measures to minimize the to that person or other persons There are no parts by the end user within this equipment The wiring used for installation of the Alarm System and shall be insulated with PVC TFE PTFE FEP or Polyamide The equipment enclosure must be secured to the building before operation Internal wiring must be routed in a manner that prevents Excessive strain or loosening of wire on terminal Damage of conductor insulation Disposal of used batteries shall be made in accordance local waste recovery and recycling regulations Before servicing DISCONNECT the power and telephone DO NOT route any wiring over circuit boards It is the installer responsibility to ensure that a readily disconnect device is incorporated in the building permanently connected installations power supply must be Class II FAIL SAFE with double or reinforced insulation between the PRIMARY and SECONDARY circuit and be an approved type acceptable to the local authoriti