DSC Strata3D inis en fr sp fm

File Preview
File Preview
Click below to download for free

File Data

Name dsc-strata3d-inis-en-fr-sp-fm-1340672589.pdf
Type PDF
Size 690.97 KB
Downloads

Text Preview

Installation Instructions d Installation de Instalaci the Detector a location that will provide the coverage required Consider the following to avoid false alarms Do not aim the detector at reflective surfaces such as mirrors or windows as this may distort the coverage pattern reflect sunlight directly onto the detector Avoid locations that are subject to direct high air flow such as near an air duct outlet Do not locate the detector near sources of moisture such as steam or oil Do not limit the coverage by placing large obstructions in the detection area such as plants or cabinets The detector should be mounted facing perpendicular to the expected intrusion route the Detector open the case use a small flat head screwdriver to push down on the tab and pull cover downward Mounting the backplate down on its back on a flat surface Position the blade of a flat head screwdriver at the midpoint of the located between the housing and the swivel knockout Press down on the screwdriver to pierce the plastic then pry to break off the knockout Remove any rough edges the system wiring through the back of the swivel bracket Secure the bracket in the desired position using the mount hardware provided With the bracket firmly mounted position the socket of the rear housing over the ball of the brack Install the washer over the threaded wire conduit making sure that the pivot pin of the washer is seated in its socket on rear housing Install the securing nut and tighten just enough to hold all components together Connect all wiring to the strip on the backplate as per diagram Figure 3 Adjust the orientation of the housing to suit the installation con Hand tighten the securing nut until the detector is held firmly in place Using a pair of pliers turn the securing nut additional rotation to complete the bracket installation Over tightening of the securing nut may result in stripping of the threads Mounting the swivel mount is not being used use a small screwdriver to remove the appropriate mounting screw and wiring knock from the backplate Mount the backplate to the wall Connect wiring as per diagram Figure 3 the front plate will operate on alarm will not operate on mode the tabs located at the bottom of the frontplate into the slots at the bottom of the backplate Tilt the front plate up towards the terminal strip When the pins on the PCB meet the terminal strip ensure that the pins are properly When the mounting tab is snapped into place tighten the screw and insert the screw cover in the front plate and it into place a typical environment the unit should be set to J2 ON If the environment presents potential disturbances cannot be avoided set J2 to J2 OFF Do not use setting with curtain mirror Test NOTE Upon installation the unit should be thoroughly tested to verify proper operation detector should be walk tested weekly by the end user and annually by the installer power up if J1 is ON the LED will blink on and off at one second intervals for 50 seconds To begin the walk test J1 to ON Once the detector has been oriented create motion in the entire area where coverage is desired by walking to the mirror pattern Should the coverage be incomplete re adjust or re locate the detector Once coverage as required the alarm LED may be disabled if desired by setting J1 to OFF Always perform a walk test after repositioning the detector du d un emplacement qui permet d obtenir la couverture requise Afin d les fausses alarmes veuillez tenir compte de qui suit N orientez pas le d vers des surfaces r telles que des miroirs ou fen ceci pourrait entra une du champ de d ou la r des rayons du soleil directement sur le d les emplacements qui sont sujets un fort courant d air comme par exemple pr d un conduit d air Ne placez pas le d pr d une source d humidit telle que de la vapeur ou de l huile Ne limitez pas la couverture du d en pla des objets imposants dans le champ de d comme par exem des plantes ou des armoires Le d doit install perpendiculairement la route pr qu l ouvrir le bo utilisez un petit tournevis t plate et poussez l sur les languettes de fixation qui sont situ la partie sup du couvercle avant Tirez ensuite le couvercle vers le bas sur un support de montage la partie arri du d sur une surface plane Placez la lame d un tournevis t plate au centre de la rainure situ le bo et le disque d du support pivotant Appuyez sur le tournevis afin de perforer le plastique et ensuite forcez afin de d le disque d Nettoyez les rebords Faites passer le c d alimentation derri le support soutien pivotant l aide de la quincaillerie fournie fixez le support de montage la position d Une fois le support de fermement ancr placez la douille de la partie arri du bo sur la boule du support de montage Installez la rondelle le conduit de fils filet en vous assurant que la patte de pivot de la rondelle est bien assise sa position sur la partie arri du Installez l de fixation et serrez le juste assez pour maintenir ensemble toutes les composantes Raccordez tous les fils bornes de raccordement situ sur le circuit tel que d dans les instructions d installation Ajustez l orientation du bo fonction des besoins de l installation Serrez l de fixation la main jusqu ce que le d soit maintenu solidement place l d pince serrez l de fixation de de tour suppl afin de compl l du support Les filets peuvent endommag si l de fixation est serr excessivement au mur vous n utilisez pas le support de montage pivotant utilisez un petit tournevis afin de retirer les vis de montage pr cet et les disques d de la plaque arri Installez la plaque arri sur le mur Faites les raccordements du c en r aux instructions fournies en place de la plaque avant del Detector una localizaci que proporcione la cobertura requerida Considere lo siguiente para evitar alarmas falsas No dirja el detector hacia superficies reflectantes tales como espejos o ventanas ya que esto puede distorcionar el de cubrimiento o reflejar la luz solar directamente al detector Evite ubicaciones que est sujetas directamente a una corriente alta de aire tales como cerca a un conducto de No coloque el detector cerca origenes de humedad como vapor o aceite No limite el cubrimiento por grandes obstrucciones en el de detecci tales como plantas o gabinetes met El detector debe ser montado apuntando perpendicularmente a la posible ruta de intrusi abrir la cubierta use un destornillador peque de hoja recta y cuidadosamente empuje la leg en la parte superior la cubierta frontal y tire la cubierta hacia abajo con Soporte la cubierta anterior con la parte posterior en una superficie plana Coloque la hoja del destornillador de hoja recta al medio de la ranura colocada entre la cubierta y el prepunzonado de giratorio Presione con el destornillador para el pl y luego lev para remover el prepunzonado Despeje cualquier borde desigual el cableado del sistema por la parte posterior de la plaqueta giratoria Asegure la plaqueta en la posici deseada la ferreter de montaje provista Con la plaqueta montada firmemente coloque el manguito de la cubierta posterior la r de la plaqueta Instale la arandela sobre el conducto roscado del cable asegurando que el perno pivote de arandela est sentado en su manguito en la cubierta posterior Instale la tuerca de aseguramiento y apri solamente suficiente para tener todos los componentes juntos Conecte todo el cableado a la regleta de conexi en la placa poste de acuerdo a las instrucciones provistas Ajuste la orientaci de la cubierta para acomodar las condiciones de insta Aprete m

Related Files