DSC System I Operating Instructions

Sur Gard System I Manual 1.1 This manual contains information regarding product use and function in addition to manufacturer and restrictions pertaining to it The entire manual should be read carefully Description of the Equipment and Classification SG System I Safety Instructions SG SYSTEM I equipment is a CLASS 1 DESK TOP MOVABLE OR RACK MOUNTED FIXED STATIONARY EQUIPMENT PLUG TYPE A using a DETACHABLE POWER SUPPLY CORD it is designed to be INSTALLED OPERATED and MAIANTAINED by SER PERSONS ONLY person having appropriate technical training and experience necessary to be aware of hazards to which that person may be in performing a task and of measures to minimize the risks to that person or other persons The equipment SG SYSTEM I shall be installed RESTRICTED ACCESS LOCATIONS within an environment that provides the Pollution Degree max 2 and over voltages category II non haz locations indoor only POWER SUPPLY CORD serves as a means of disconnection from the MAINS The OUTLET used to power the equipment shall be installed near equipment and shall be easily accessible The equipment must be connected to a socket outlet with a protective grounding electrode conductor RACK MOUNTED IT IS THE RESPONSIBILITY OF THE INSTALLER TO ENSURE THAT THE FINAL ASSEMBLY that includes SG I EQUIPMENT IS COMPLIANT with the applicable requirements from the point of view of STABILITY the rack mounted equipment must secured to the building structure before operation all wiring and installation shall be in accordance with electrical codes acceptable to the authori that have jurisdiction where the equipment is installed serviced and operated not more than 3 three SG System I units mounted within the same shall be powered from the same branch circuit use a different branch circuit for any group larger than 3 three units cables shall be routed in a manner that prevents excessive strain on wire and on terminal connections loosening of terminal connec damage of conductor insulation This product used Lithium Batteries Improper handling of lithium batteries may result in heat generation or fire which may lead to personal injury TO THE MAINS the DETACHABLE POWER SUPPLY CORD to the IEC 320 connector located on SG System I equipment The Ethernet communication lines must be connected first to an Approved acceptable to the local authorities type NID Network Inter Device before leaving the premises e g UL Installations UL60950 Listed NID for ULC Installations CAN CSA C22.2 No 60950 1 Listed REPAIRS IN THE FIELD ARE ALLOWED THE EQUIPMENT SG System I MUST BE RETURNED TO THE MANUFACTURER FOR Considerations unit is to be installed and used in an environment that provides pollution degree max 2 and overvoltages category II indoors in a non hazardous only The SG System I is intended to be installed operated and maintained by Service Persons only in restricted access locations The equip is included within a metallic enclosure that fulfills all of the applicable requirements for a fire enclosure The enclosure cannot be opened without use of a tool installing connecting or operating the SG System I take care to observe the following precautions Connect the connection cable to the appropriate socket Ensure that the cables are laid out in such a way that accidents cannot occur Connected cables must not be subject to excessive mechanical strain Use only authorised accessories with this equipment Protect the receiver from moisture dust liquids and vapors Safety Guidelines Never install telephone wiring during an electrical storm Read these instructions and save for later reference Follow all warnings and instructions as marked on the product Unplug the receiver from the mains power and telephone line sockets prior to cleaning Use only a soft damp cloth to clean the device Do not abrasive liquids or chemicals to clean the device Do not place this product on an unstable cart stand or table The receiver may fall causing serious damage to the product and the operator Unplug the receiver from the mains power and telephone line sockets and refer servicing to qualified service personnel under the following When the mains power cord is frayed or the plug is damaged If liquid has been spilled into the receiver or exposed to rain or water If the receiver does not operate normally when the operating instructions are followed If the receiver exhibits a distinct reduction in performance COMPLIANCE STATEMENT Changes or modifications not expressly approved by Digital Security Controls could void your authority to use this equipment equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or of the following measures Re orient the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio television technician for help user may find the following booklet prepared by the FCC useful How to Identify and Resolve Radio Television Interference Problems This is available from the U S Government Printing Office Washington D C 20402 Stock 004 000 00345 4 INFORMATION equipment complies with Part 68 of the FCC Rules and the requirements adopted by the ACTA On the side of this equipment is a label that con among other information a product identifier in the format US AAAEQ TXXXX If requested this number must be provided to the Telephone identifier US F53AL01BSYSTEM1 Jack RJ 11 Connection Requirements plug and jack used to connect this equipment to the premises wiring and telephone network must comply with the applicable FCC Part 68 rules and adopted by the ACTA A compliant telephone cord and modular plug is provided with this product It is designed to be connected to a modular jack that is also compliant See installation instructions for details Equivalence Number REN REN is used to determine the number of devices that may be connected to a telephone line Excessive RENs on a telephone line may result in the not ringing in response to an incoming call In most but not all areas the sum of RENs should not exceed five 5.0 To be certain of the num of devices that may be connected to a line as determined by the total RENs contact the local Telephone Company For products approved after 23 2001 the REN for this product is part of the product identifier that has the format AAAEQ TXXXX The digits represented by are the REN without a decimal point e g 03 is a REN of 0.3 For earlier products the REN is shown on the label of Harm this equipment SG SYSTEM I causes harm to the telephone network the telephone company will notify you in advance that temporary discontinu of service may be required But if advance notice is not practical the Telephone Company will notify the customer as soon as possible Also you be advised of your right to file a complaint with the FCC if you believe it is necessary in Telephone Company Equipment or Facilities Telephone Company may make changes in its facilities equipment operations or procedures that could affect the operation of the equipment If happens the Telephone Company will provide advance notice in order for you to make necessary modifications to maintain uninterrupted service Maintenance Facility trouble is experienced with this equipment SG SYSTEM I for repair or warranty information please contact the facility indicated below If the is causing harm to the telephone network the Telephone Company may request that you disconnect the equipment until the problem is This equipment is of a type that is not intended to be repaired by the end user c o APL Logistics 757 Douglas Hill Rd Lithia Springs GA 30122 Information to party line service is subject to state tariffs Contact the state public commission public service commission or corporation commission for dialing equipment must be able to seize the telephone line and place a call an emergency situation It must be able to do this even if other equipment tele answering system computer modem etc already has the telephone line in To do so alarm dialing equipment must be connected to a properly installed jack that is electrically in se