DSC System II Operating Instructions

Sur Gard System II Line Network Receiver This manual contains information on limitations regarding use and function and information on the limitations as to of the manufacturer The entire manual should be carefully read Manual 2.0 DESCRIPTION of the EQUIPMENT and CLASSIFICATION II SAFETY INSTRUCTIONS SYSTEM II equipment is a CLASS 1 DESK TOP MOV or RACK MOUNTED FIXED STATIONARY PLUGGABLE TYPE A using a DETACHABLE SUPPLY CORD it is designed to be INSTALLED and MAINTAINED by SERVICE PERSONS person having appropriate technical training and experi necessary to be aware of hazards to which that person may exposed in performing a task and of measures to minimize the to that person or other persons The equipment SYSTEM II be installed in RESTRICTED ACCESS LOCATIONS an environment that provides the Pollution Degree max 2 overvoltages category II non hazardous locations indoor POWER SUPPLY CORD serves as a means of disconnec from the MAINS The OUTLET used to power the equip shall be installed near the equipment and shall be easily The equipment must be connected to a socket outlet a protective earthing connection RACK MOUNTED IT IS THE RESPONSIBILITY OF INSTALLER TO ENSURE THAT THE FINAL ASSEM that includes SYSTEM II EQUIPMENT IS COMPLIANT the applicable requirements from the point of view of STA the rack mounted equipment must be secured to the structure before operation all wiring and installation be in accordance with electrical codes acceptable to the that have jurisdiction where the equipment is serviced and operated not more than 3 three system II mounted within the same rack shall be powered from the branch circuit use a different branch circuit for any group than 3 three units cables shall be routed in a manner that prevents strain on wire and on terminal connections loosening terminal connections damage of conductor insulation product uses Lithium Batteries Improper handling of lith batteries may result in heat generation explosion or fire may lead to personal injuries TO THE MAINS Connect first the DETACHABLE POWER SUPPLY CORD to IEC 320 connector located on SYSTEM II equipment The Ethernet communication lines must be con first to an Approved acceptable to the local authorities NID Network Interface Device before leaving the prem e g UL installations UL60950 Listed NID for ULC Instal CAN CSA C22.2 No 60950 1 Listed NID REPAIRS IN THE FIELD ARE ALLOWED THE EQUIP SYSTEM II MUST BE RETURNED TO THE MANU FOR REPAIRS Compliance Statement Changes or modifications not expressly approved by Digital Security Controls void your authority to use this equipment equipment has been tested and found to comply with the limits for a Class B digital device to Part 15 of the FCC Rules These limits are designed to provide reasonable protection harmful interference in a residential installation This equipment generates uses and can radio frequency energy and if not installed and used in accordance with the instructions cause harmful interference to radio communications However there is no guarantee that will not occur in a particular installation If this equipment does cause harmful to radio or television reception which can be determined by turning the equipment Class B digital apparatus complies with Canadian ICES 003 appareil num de la classe B est conforme la norme NMB 003 du Canada and on the user is encouraged to try to correct the interference by one or more of the follow measures Re orient the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is Consult the dealer or an experienced radio television technician for help user may find the following booklet prepared by the FCC useful to Identify and Radio Television Interference Problems This booklet is available from the U S Gov Printing Office Washington D C 20402 Stock 004 000 00345 4 of Contents 1 Introduction 1 1.1 Features 1 1.2 Software Compatibility 1 1.3 Approvals 1 Industry Approvals 1 1.4 Specifications 3 1.5 Out of Box 3 2 Installation 4 2.1 Controls and Indicators 4 2.2 Set Up and Testing 6 3 Operation Operating Modes 7 3.1 Active Mode 7 3.2 Manual Mode 7 3.3 Program Category 7 7 User Interface 7 Top Level Menu 7 System Functions Menu 8 Miscellaneous LED Indicators 9 4 System Options 10 4.1 System Option Index 10 4.2 System Options 11 001 LAN IP Address 11 002 LAN Subnet Mask Address 10 003 LAN Gateway 11 004 Auto Update Time and Date 11 005 Contrast 11 006 Password 11 007 Automation Baud Rate 11 008 Automation Data Bits 11 009 Automation Parity 12 00A Serial Printer Format 12 00B Serial Baud Rate 12 00C Serial Data Bits 12 00D Serial Printer Parity 12 00F B32 Headers 12 00F B32 Headers 12 012 Heartbeat Timer 12 013 Buzzer Tone 13 014 Receiver Number 13 015 Printer Test 13 020 Mask UPS AC 13 021 Mask UPS BAT 13 024 Mask SG TCP IP 13 025 Mask SG Serial 14 028 Mask TCP Printer 14 029 Mask Parallel Printer 14 02A Mask Serial Printer 14 02F Automation Mode 14 030 Printer Mode 16 031 ACK Wait 16 032 Date Format 16 037 and 038 Product ID Keys 1 2 16 039 Mask USB Printer 16 03A Programmable I O 16 03B Last Message On 16 03C LCD Backlight Colour 17 03D Key Backlight Colour 17 041 System Number Length 17 042 Busy Out 17 043 System Protocol ID 17 5 System Options 10 5.1 IP Option Index 19 5.2 IP Options 19 110 Line Card Number Table 1 20 113 Transmitter Failure Debounce Time 20 115 Transmitter Restoral Debounce Time 20 119 Mask Transmitter Restoral 20 11A Mask Transmitter Failure 20 11B Mask Transmitter Swap 20 11C Mask Transmitter Unencrypted 20 11D Mask Invalid Report 20 11E Mask Unknown Account