DSC Test SCW9047 manual

Installation Guide Contained Wireless Alarm System v1.0 This manual contains information on limitations regarding product use and function and on the limitations as to liability of the manufacturer The entire manual should be carefully read INSTRUCTIONS for SERVICE PERSONNEL When using equipment connected to the TELEPHONE NETWORK there are basic safety instructions should always be followed Refer to the SAFETY INTRUCTIONS provided with this product save them for reference Instruct the end user regarding the safety precautions that shall be observed when operating this Installing The Equipment NOT use a sharp or metal object to open the packaging your package includes the following items Guide Manual including the SAFETY INSTRUCTIONS and SAVE These Instructions All WARNINGS AND INSTRUCTIONS specified within these Instruction and or on the equipment SCW904x Supply Direct Plug In Mounting Hardware A Suitable Location For The Alarm Controller the following list as a guide to find a suitable place for this equipment it near a telephone socket and a power outlet a place that is free from vibration and shocks the Alarm Controller on a flat stable surface and follow the Installation suggestions NOT locate this product where persons will walk on the secondary circuit cable s NOT use extension cords to PLUG IN the Power Supply of this equipment setting up the equipment near heaters air conditioners ventilators and or refrigerators NOT connect the Alarm Controller to electrical outlets on the same circuit as large appliances NOT select a place that exposes your alarm controller to direct sunlight excessive heat moisture vapors chemicals or dust NOT install this Equipment near water e g Bath Tub Wash Bowl Kitchen Laundry sink In a wet basement or near swimming pool etc NOT install this equipment and its accessories in areas where there is a risk of explosion NOT connect this Alarm Controller to electrical outlets controlled by wall switches or automatic timers avoid interference sources Precautions required during Installation install this EQUIPMENT and or TELEPHONE WIRING during A Lightning Storm touch uninsulated Telephone wires or Terminals unless the telephone line has been disconnected at the network interface that Cables are positioned so that accidents can not occur Connected Cables must NOT be subject to excessive mechanical strain Only the Power Supply supplied with this equipment Use of unauthorized power supplies may cause damage AC Socket Outlet powering the equipment shall be located near the equipment and shall be easily accessible EQUIPMENT HAS NO MAINS ON OFF SWITCH THE PLUG OF THE DIRECT PLUG IN POWER SUPPLY IS INTENDED TO SERVE AS DISCONNECTING DEVICE IF THE EQUIPMENT MUST BE QUICKLY DISCONNECTED IT IS IMPERATIVE THAT ACCESS TO THE PLUG AND ASSOCIATED MAINS SOCKET OUTLET IS NEVER OBSTRUCTED of Contents Wiring 1 2 3 Zone Wiring 3 PGM AUX Power Wiring 3 Telephone Line Wiring 3 Battery 3 AC Wiring 3 Device Enrollment 5 Programming 7 Programming 10 programming with PC Link 10 Programming via telephone line 10 11 Arming 11 Arming 11 11 Commands 11 keys 13 Programming 14 to Program 14 Toggle Options 14 Decimal Hexadecimal Data 14 to Exit Installer Programming 14 Programming 14 Worksheets 15 Programming Worksheets 15 Worksheets 16 Descriptions 33 Troubleshooting 48 A Code Formats Contact ID SIA 50 B Format Options 52 C Approvals Information 54 D False Alarm Reduction Quick Reference Chart 56 E Audio Verification 57 1 Installation Wiring 1 Installation Wiring Installation Guide provides the basic installation wiring and programming information for the PowerSeries Self Contained SCW Security System publication covers the following versions of the SCW Security System v1.0 v1.0 SUMMARY v1.0 v1.0 models are not UL ULC Listed intended for European market only Range 0 32 Max 93 RH Non Condensing Supply 16.5VAC 20VA 50 60Hz Draw from Transformer 400mA AC Max Output 12.0 12.5VDC 100mA Zones 32 I O 2 1 Keys 16 Codes 16 1 Master Code Buffer 128 Events Display 2 Rows x 16 Char Transformer Secondary 16.5 VAC 20 40VA Backup 7.2VDC 1500 mAH Backup I O Terminals can be configured as Zone Inputs or PGM Outputs When configured as PGMs outputs are 50mA equipment SCW Alarm System shall be installed and used an environment that provides the pollution degree max 2 over voltages category II NON HAZARDOUS LOCATIONS only The equipment is DIRECT PLUG IN connected and designed to be installed serviced and or repaired by service only service person is defined as a person having appropriate technical training and experience necessary to aware of hazards to which that person may be exposed in a task and of measures to minimize the risks to that or other persons