DSC TL-250 Stand Alone Quick Install Guide WEB

File Preview
File Preview
Click below to download for free

File Data

Name dsc-tl-250-stand-alone-quick-install-guide-web-4950178623.pdf
Type PDF
Size 618.75 KB
Downloads

Text Preview

Install Guide February 2 2006 Stand Alone Quick Install Guide Receivers III with a DRL3 IP line card Overview T LINK TL250 is a network communicator that sends alarm system information to the central and allows you to also perform uploads and downloads of the panel through the DLS T LINK TL250 has four modes of operation It can operate in one of three operational modes it could be connected to a compatible DSC panel Mode The system is configured as a communicator with a compatible DSC 1 Follower 2 Panel 3 Panel panel T LINK TL250 monitors the Bell Output of the control panel The identifies the Bell Output cadence and transmits the Fire or Burglar alarm reporting code to the central T LINK TL250 system is configured for 4 zones stand alone the T LINK TL250 detects a PC5108 expander card on power up it automatically configure itself for 12 zone standalone operation with closed loops you Begin programming the T Link TL250 module obtain the following information from the Network The static IP address for the T Link TL250 module only if static IP address is going to be The subnet mask for the T Link TL250 module only if static IP address is going to be The receivers IP address The gateway IP address Install Guide 1 Resetting to Factory Defaults Defaults Remove Power from the T Link TL250 disconnect battery and the control panel if Connect a jumper wire between the PGM1 and IN1 terminals Apply power to the system Wait approximately 20 seconds then remove the short between PGM1 and IN1 2 Programming T Link TL250 can be programmed remotely or locally with the T Link console via the connection or locally with the T Link console via the serial port TL250 programming be done using DLS software On a default unit the T Link can be reached from the console at IP 192.168.0.99 with subnet mask of 255.255.255.0 on port 3064 Program the static IP address for the T Link TL250 module Section 001 Program for DHCP Program the subnet mask for the T Link TL250 module Section 002 This option will ignored if the unit is set for DHCP Program the static IP address of the receiver Section 007 Program the T Link TL250 account number Section 003 the receiver is on a different network segment than the T Link TL250 module the address associated with the T Link TL250 module must be programmed 008 Program the Digital Input 1 through 12 Select the definition from the list below Section Input Input 24 hr Fire Input 24 hr Burglary Panic Input Tamper Key switch Arm Input Input 2 Only Bell Follower Input Input 1 Only Program the zone Input 1 Configuration Section 048 0 for normally open inputs 1 for normally closed inputs Install Guide Program the zone Input 2 to 4Configuration Section 049 0 for normally open and 1 for normally closed inputs Program the Fire On Time The Bell Pulse ON Time is used with Digital Input 1 when for Bell Follower mode The Bell Pulse ON OFF Time is the time of the pulse This option is programmed in hex times 100 milliseconds Section 062 Program the Fire Off Time The Bell Steady ON Time is used with Digital Input 1 when for Bell Follower mode This the minimum time in 100ms increments that the must be active sounding before it will be considered a steady on state and generate Burglary Alarms This option is programmed in hex times 100 milliseconds Section After all T Link TL250 module programming is complete you must restart the module so programming changes will take effect To restart the T Link Tl 250 module enter the 55 in T Link TL 250 programming section 999 and wait 15 seconds for the to reboot Once complete press the key to exit T Link TL250 programming Verify that the STAT LED is flashing once every 5 seconds if not please procedure to the Trouble Shooting section Call the Central Station and put your account on test Trip a zone on the control panel Call the Central Station and verify that the correct signal was received 4 Testing Install Guide Shooting LED Diagnostics LED will turn on when the network is present and will blink when there is network activity LED will remain off for 10BaseT network connection and will be on to indicate 100BaseT connection will blink to show network activity Status The STAT Status LED will normally blink once every 5 seconds Should a be present the LED will blink a number of times as per table with a one second pause restarting the sequence Should there be more then one trouble present the LED will blink a rate that is equal to the highest priority The transmitter has a number of individually trouble conditions that report various troubles present on the transmitter Blinks Absent Account 1 Absent Ethernet link between the transmitter and local hub or router is absent is equivalent to the link LED on the Ethernet chip being off transmitter account code is still set to the default value of FFFFFF transmitter is not receiving Receiver Heartbeat commands from the the case of a DSC 4020 or 5020 panel the transmitter is not receiving from the panel through the PC Link interface In the case of a generic the panel is not supervised by the transmitter are Inputs on the T Link which are in the alarm condition failed to communicate with receiver 1 PC5108 Module is not responding to the transmitter PC5108 Module Tamper has been activated failed to communicate with receiver 2 system was armed by the key switch zone is being programmed remotely Alarms 1 Absent Tamper 2 switch Arm Remote Local at any point you experience any problems of have additional questions in reference to operation of the T Link TL 250 please call the DSC Technical Support department at Monday to Friday 8am 8pm EST transmitter is not able to connect to receiver 2 on power up is being programmed locally

Related Files