DSC WLS904P - Installation DSC Manual - English - French - Spanish - Wireless Pet-Immune Passive Infrared Motion Detector

WLS904P Installation Instructions in 433 and 900MHz d WLS904P dans 433MHz et 900MHz de Instalaci WLS904P en 433MHz y 900 MHz Mount the detector flat on a wall or in a corner Do not angle it downwards or use mounting brackets with this detector d est utilis et que des animaux domestiques sont pr WLS904P detector is designed to combine the convenience of a wireless detector with effective and reliable detection of human as well as good protection against the nuisance alarms associated with pets weighing up to 60 lbs 27.3kg the Detector WLS904P detector provides effective immunity to single or multiple pets whose total combined weight does not exceed 60 lbs when installed and configured in the following manner a detector location that will provide the coverage required and will allow the detector to be mounted a minimum of 6 ft high and not higher than 10ft 3m 7 ft 2.3m recommended the following to avoid false alarms Do not aim the detector at a stairwell to which a pet has access Do not place furniture or objects higher than 3ft 0.9m which a pet can climb onto e g a cat on a couch closer than 1.8m from the detector it is used in conjunction with pets sunlight directly onto the detector Do not aim the detector at reflective surfaces such as mirrors or windows as this may distort the coverage pattern or Avoid locations that are subject to direct high air flow such as near an air duct outlet Do not locate the detector near sources of moisture such as steam or oil Do not limit the coverage by large obstructions in the detection area such as plants or cabinets For indoor use only No detector should be mounted without first performing a module placement test to determine that it is in range of wireless receiver See the Placement Test instructions in the Instruction Sheet for your receiver or in the Installation Man for your system a location has been selected remove the plastic from the mounting holes and locate the backplate on the wall and mark screw It is suggested that wall anchors be used for all screw locations Secure the backplate to the wall and then secure the enrolled to its backplate The coils and antenna on the WLS904P circuit board are very sensitive components precisely adjusted for maxi performance Do not touch the coils or antenna Even minor distortions can affect the performance of the motion detector a WLS904P the back of the PIR housing there will be two serial numbers a five digit number and a six digit number Please refer to your Installation Manual for information on which serial number should be enrolled the Sensitivity Setting WLS904P features and settings on jumper J1 which is used to configure the detector for the weight of the and the environment For an environment with a single pet whose weight does not exceed 30lbs 13.6kg the jumper should set to setting In an environment with single or multiple pets whose combined weight is greater than 30lbs 13.6kg but greater than 60 lbs 27.3kg the jumper must be set to the setting When the detector is mounted 6 ft to 7 ft 1.95 to 2.3 m or there is the possibility of the pet getting higher than 4ft 1.2 m the slow setting must be used change the setting from Slow to Fast move the jumper over one pin as shown in the diagram Traffic Shutdown Mode prolong battery life the motion detector uses a feature called High Traffic Shutdown When motion is detected the device will transmit to receiver and will then shut down for three minutes If motion is detected again during the shutdown time the unit will not transmit the to the receiver The detector will thus remain in the shutdown mode until three minutes after the first motion detected was transmitted detector will transmit detected motion every three minutes High Traffic Shutdown Mode affects testing the motion detector in two ways performing the module placement test the unit must be tampered by removing the unit from the backplate and replacing it The test cannot be performed by creating motion in front of the device performing a system test the unit must be left idle for three minutes before testing can be performed Once three minutes has passed motion in front of the detector to see if the device is both detecting motion and transmitting to the receiver Refer to the PC5132 or the system Installation Instructions for UL ULC requirements For UL ULC installations where WLS904P is used on entry or exit delay zones the entry delay must not be longer than 39 seconds and the exit delay not be longer than 54 seconds Detector Transmission Delay motion detector transmission is always delayed by six seconds This is necessary to prevent false alarms caused by a motion sensor before a delay zone has a chance to report This six second delay cannot be altered or disabled Test Mode motion detector has a walk test mode which will activate an LED for testing purposes During normal operation the LED will not on put the detector in walk test mode create a tamper by removing the detector from its backplate and then replacing it Each time the senses motion it will turn on the red LED Five seconds after motion is detected the detector will send a signal to the receiver the LED will flash rapidly 5 times The detector will be in walk test mode until it has sent 10 transmissions verify the pet immunity of the detector place the animal s within the coverage area and then move out of the zone Encourage the to move around as it normally would and ensure that it moves across the detection pattern of the detector Verify that no alarm is Pet Immunity not verified by UL WLS904P est con pour combiner la commodit d d sans fil avec la d efficace et fiable du mouvement humain et bonne protection contre la nuisance des fausses alarmes li des animaux domestiques pesant un maximum de 27,3 kg 60 lbs du d WLS904P offre une immunit efficace contre un ou plusieurs animaux domestiques dont le poids total ne d pas 27,3 kg lbs lorsqu est install et configur comme suit un emplacement qui offrira la couverture requise et permettra au d d install une hauteur minimum de 1,95m pi et maximum de 3m 10 pi 2,3 m 7,5 pi recommand Tenez compte des suivants pour les fausses alarmes Ne placez pas le d face un escalier auquel un animal domestique a acc Ne placez pas de meuble ou d d hauteur de plus de 0,9 m 3 pi sur lequel un animal domestique peut grimper par un chat sur un sofa moins de 1.8 m 6 pi du d Installez le d plat sur un mur ou dans un coin Ne l pas vers le bas et n pas de support de montage lorsque Ne placez pas le d en face de surfaces r telles que des miroirs ou des fen car elles pourraient d diagramme de rayonnement ou r la lumi solaire directement sur le d les emplacements o le d pourrait expos un courant d intense comme une sortie de gaine de circulation Ne placez pas le d pr de sources d telles que de la vapeur d ou d Ne limitez pas la couverture en pla des objets importants dans la zone de d telles que des plantes ou des armoires Pour utilisation int seulement N d aucun d avant d fait un essai de placement de module pour d s se dans la port du r sans fil Voir les instructions d d dans la Notice d de votre ou dans le Manuel d de votre syst emplacement a trouv retirez le plastique des trous de montage placez la plaque arri sur le mur et marquez des vis Nous vous sugg d des ancres pour toutes les vis Fixez la plaque arri au mur puis fixez le sur sa plaque arri Les selfs et l sur la carte circuit imprim sont des tr sensibles r avec pr pour meilleure performance Ne touchez ni les selfs ni l M des d minimes peuvent affecter la perfor du d de mouvement d WLS904P y a deux num de s au dos du coffret PIR Un num cinq chiffres et un num six chiffres Pour de plus amples