DSC WLS908 UM EN NA R001

FCC COMPLIANCE STATEMENT Changes or modifications not expressly approved by Digital Security Controls Ltd could void your to use this equipment equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a installation This equipment generates uses and can radiate radio frequency energy and if not installed used in accordance with the instructions may cause harmful interference to radio communications However is no guarantee that interference will not occur in a particular installation If this equipment does cause interference to radio or television reception which can be determined by turning the equipment off and on user is encouraged to try to correct the interference by one or more of the following measures Re orient the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio television technician for help user may find the following booklet prepared by the FCC useful to Identify and Resolve Radio Interference Problems This booklet is available from the U S Government Printing Office Washing D C 20402 Stock 004 000 00345 4 Security Controls Ltd 160 Washburn St Lockport NY 14094 device complies with RSS 210 of Industry Canada Operation is subject to the following two conditions 1 device may not cause interference and 2 this device must accept any interference including interference that cause undesired operation of the device dispositif satisfait aux exigences d Canada prescrites dans le document CNR 210 son utilisation est seulement aux conditions suivantes 1 il ne doit pas produire de brouillage et 2 l du doit pr accepter tout brouillage radio re m si ce brouillage est susceptible de le fonctionnement du dispositif WARRANTY Security Controls Ltd warrants that for a period of twelve months from the date of the product shall be free of defect in materials and workmanship under normal use that in fulfilment of any breach of such warranty Digital Security Controls Ltd shall at its repair or replace the defective equipment upon return of the equipment to its repair This warranty applies only to defects in parts and workmanship and not to damage in shipping or handling or damage due to causes beyond the control of Digital Security Ltd such as lightning excessive voltage mechanical shock water damage or arising out of abuse alteration or improper application of the equipment foregoing warranty shall apply only to the original buyer and is and shall be in lieu of any all other warranties whether expressed or implied and of all other obligations or liabilities on part of Digital Security Controls Ltd This warranty contains the entire warranty Digital Controls Ltd neither assumes nor authorizes any other person purporting to act on its to modify or to change this warranty nor to assume for it any other warranty or liability this product no event shall Digital Security Controls Ltd be liable for any direct indirect or consequential loss of anticipated profits loss of time or any other losses incurred by the buyer in with the purchase installation or operation or failure of this product Digital Security Controls Ltd recommends that the entire system be completely on a regular basis However despite frequent testing and due to but not limited to tampering or electrical disruption it is possible for this product to fail to perform expected 2001 Digital Security Controls Ltd in Canada 29001920 R1 Panic Pendant INSTRUCTIONS WLS908 Wireless Panic Pendant is a device designed to transmit a emergency signal from any location within the range of the Wireless Receiver software version 2.0 or higher Signals will transmitted whether the system is armed or not pendant can be attached to a necklace or a belt clip The unit is even and lightweight enough to be placed in a shirt pocket or tucked a purse The pendant is also water resistant will not be transmitted if the pendant is not within the of the wireless receiver activate an alarm press and hold both outer buttons for two seconds the pendant pendant should be tested on a weekly along with the rest of your alarm system full system testing instructions please your PC5010 Instruction manual To the pendant Begin testing when your system is in the state and the keypad Ready light is ON Press and hold the small middle button on pendant marked for two seconds the test has completed and the battery condition is normal the will turn off for four to five seconds If the pendant battery is low the keypad light will turn ON and a series of keypad beeps will be heard If a low battery condition is you must inform your installer to have the unit replaced you have the PC5132 RS Wireless Receiver software version 2.0 a alarm will occur when the test button is pressed If you have receiver you MUST call your monitoring station before pressing test button to alert them that you are testing the panic pendant