DSC WLS909 UM EN NA R002
File Preview
Click below to download for free
Click below to download for free
File Data
Name | dsc-wls909-um-en-na-r002-2986534710.pdf |
---|---|
Type | |
Size | 736.31 KB |
Downloads |
Text Preview
Testing the WLS909 Key test the batteries on your key press and hold one of the arm or disarm buttons for seconds If the batteries are low the Trouble light on any of your system keypads turn ON If the Trouble light turns ON the key batteries must be replaced Pressing another button after completing the test may clear the trouble The key batteries must still be replaced not use a Fire Auxiliary or Panic key to test your WLS909 unit as pressing these will always notify your monitoring station of a non medical emergency replace the batteries remove the screw on the back of the and carefully separate the two sides of the key plastic Remove the old batteries from between the two metal Insert the new batteries according to the diagram at right reattach the two sides of the key plastic casing The requires LR44 The polarity of the batteries must be observed batteries of WARRANTY Security Controls Ltd warrants that for a period of twelve months from the date of purchase the product be free of defect in materials and workmanship under normal use and that in fulfilment of any breach of warranty Digital Security Controls Ltd shall at its option repair or replace the defective equipment upon of the equipment to its repair depot This warranty applies only to defects in parts and workmanship and to damage incurred in shipping or handling or damage due to causes beyond the control of Digital Controls Ltd such as lightning excessive voltage mechanical shock water damage or damage out of abuse alteration or improper application of the equipment foregoing warranty shall apply only to the original buyer and is and shall be in lieu of any and all other whether expressed or implied and of all other obligations or liabilities on the part of Digital Security Ltd This warranty contains the entire warranty Digital Security Controls Ltd neither assumes nor any other person purporting to act on its behalf to modify or to change this warranty nor to assume it any other warranty or liability concerning this product no event shall Digital Security Controls Ltd be liable for any direct indirect or consequential damages loss anticipated profits loss of time or any other losses incurred by the buyer in connection with the purchase or operation or failure of this product Digital Security Controls Ltd recommends that the entire system be completely tested on a basis However despite frequent testing and due to but not limited to criminal tampering or disruption it is possible for this product to fail to perform as expected COMPLIANCE STATEMENT Changes or modifications not expressly approved by Digital Security Controls Ltd could void your authority use this equipment equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential This equipment generates uses and can radiate radio frequency energy and if not installed and used in with the instructions may cause harmful interference to radio communications However there is no that interference will not occur in a particular installation If this equipment does cause harmful interference radio or television reception which can be determined by turning the equipment off and on the user is encouraged to to correct the interference by one or more of the following measures Re orient the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio television technician for help user may find the following booklet prepared by the FCC useful to Identify and Resolve Radio Television Problems This booklet is available from the U S Government Printing Office Washington D C 20402 004 000 00345 4 Security Controls Ltd 160 Washburn St Lockport NY 14094 device complies with RSS 210 of Industry Canada Operation is subject to the following two conditions 1 this device not cause interference and 2 this device must accept any interference including interference that may cause operation of the device dispositif satisfait aux exigences d Canada prescrites dans le document CNR 210 son utilisation est autoris aux conditions suivantes 1 il ne doit pas produire de brouillage et 2 l du dispositif doit pr accepter tout brouillage radio re m si ce brouillage est susceptible de compromettre le fonctionnement dispositif 1999 Digital Security Controls Ltd in Canada 29002095 R002 Key INSTRUCTIONS WLS909 wireless key allows you to arm disarm your alarm system as well as other keypad functions from a unit enough to keep in your pocket with your installer you can decide functions you wish to have accessible your portable key activate any one of the four selected press and hold the appropriate for two seconds Your installer will each function by applying a circular beside each of the four buttons will not be received if the is not within the range of the receiver Arming Arming of the most commonly used functions are as follows this button to arm your system in the Stay mode All perimeter zones be armed such as all window and door contacts but the interior zones remain inactive allowing you to stay on the premises without setting off alarm this button to arm your system in the Away mode Both the interior exterior zones will be armed allowing you to exit the premises this button to disarm your system You do not have to enter your code when you use the key to disarm the system this button to notify your central monitoring station of a fire condition this button to notify your central monitoring station of a non medical Please discuss the functionality of this button with your installer this button to notify your central monitoring station of a situation the police such as a break in options are available Please discuss all WLS909 options with your in order to program the best possible combination to suit your needs the WLS909 Key test the batteries on your key press and hold one of the arm or disarm buttons for seconds If the batteries are low the Trouble light on any of your system keypads turn ON If the Trouble light turns ON the key batteries must be replaced Pressing another button after completing the test may clear the trouble The key batteries must still be replaced not use a Fire Auxiliary or Panic key to test your WLS909 unit as pressing these will always notify your monitoring station of a non medical emergency replace the batteries remove the screw on the back of the and carefully separate the two sides of the key plastic Remove the old batteries from between the two metal Insert the new batteries according to the diagram at right reattach the two sides of the key plastic casing The requires LR44 The polarity of the batteries must be observed batteries of WARRANTY Security Controls Ltd warrants that for a period of twelve months from the date of purchase the product be free of defect in materials and workmanship under normal use and that in fulfilment of any breach of warranty Digital Security Controls Ltd shall at its option repair or replace the defective equipment upon of the equipment to its repair depot This warranty applies only to defects in parts and workmanship and to damage incurred in shipping or handling or damage due to causes beyond the control of Digital Controls Ltd such as lightning excessive voltage mechanical shock water damage or damage out of abuse alteration or improper application of the equipment foregoing warranty shall apply only to the original buyer and is and shall be in lieu of any and all other whether expressed or implied and of all other obligations or liabilities on the part of Digital Security Ltd This warranty contains the entire warranty Digital Security Controls Ltd neither assumes nor any other person purporting to act on its behalf to modify or to change this warranty nor to assume it any other warranty or liability concerning this product no event shall Digital Security Controls Ltd be liable for any direct indirect or consequential damages loss anticipated profits loss of time or any other losses incurred by the buyer in connection with the purchase or operation or failure of this product Digital Sec