DSC WLS915 - Installation Manual - English - Wireless DoorWindow Contact

FCC COMPLIANCE STATEMENT Changes or modifications not expressly approved by Digital Security Controls Ltd could void your to use this equipment equipment generates and uses radio frequency energy and if not installed and used properly in strict accordance the manufacturer instructions may cause interference to radio and television reception It has been type tested and to comply with the limits for Class B device in accordance with the specifications in Subpart of Part 15 of Rules which are designed to provide reasonable protection against such interference in any residential installation there is no guarantee that interference will not occur in a particular installation If this equipment does cause to television or radio reception which can be determined by turning the equipment off and on the user is to try to correct the interference by one or more of the following measures Re orient the receiving antenna Relocate the alarm control with respect to the receiver Move the alarm control away from the receiver Connect the alarm control into a different outlet so that alarm control and receiver are on different circuits necessary the user should consult the dealer or an experienced radio television technician for additional The user may find the following booklet prepared by the FCC helpful to Identify and Radio Television Interference Problems This booklet is available from the U S Government Printing Washington D C 20402 Stock 004 000 00345 4 Warranty Warranty Warranty Warranty Warranty Security Controls Ltd warrants that for a period of twelve months from the date of purchase product shall be free of defects in material and workmanship under normal use and that in of any breach of such warranty Digital Security Controls Ltd shall at its option repair or the defective equipment upon return of the equipment to its repair depot This warranty only to defects in parts and workmanship and not to damage incurred in shipping or handling damage due to causes beyond control of Digital Security Controls Ltd such as lightning excessive mechanical shock water damage or damage arising out of abuse alteration or improper of the equipment foregoing warranty shall apply only to the original buyer and is and shall be in lieu of any and all warranties whether express or implied and of all other obligations or liabilities on the part of Digital Controls Ltd This warranty contains the entire warranty Digital Security Controls Ltd neither nor authorizes any other person purporting to act on its behalf to modify or to change this nor to assume for it any other warranty or liability concerning this product no event shall Digital Security Controls Ltd be liable for any direct indirect or consequential loss of anticipated profits loss of time or any other losses incurred by the buyer in with the purchase installation or operation or failure of this product Security Controls Ltd recommends that the entire system be completely tested on a regular However despite frequent testing and due to but not limited to criminal tampering or electrical it is possible for this product to fail to perform as expected 2000 Digital Security Controls Ltd Canada www dsc com in Canada 29004017 R003 Transmitter INSTRUCTIONS INSTRUCTIONS INSTRUCTIONS INSTRUCTIONS INSTRUCTIONS either notched location on the cover insert the flat blade of a small between the base and the cover and twist the screwdriver pop the cover off Cover Battery care when installing the battery and observe the correct polarity see below Use only Eveready Lithium Energizer No EL123AP battery Battery may if mistreated Do recharge disassemble dispose of in fire Transmitter where the transmitter is to be mounted Perform Module Placement Test to ensure that the selected is in range of the wireless receiver see receiver Manual for instruction where the magnet will be placed In order to the reed switch the magnet must line up with the of the transmitter Circuit Board mounting the unit remove the circuit board At the notched location on base which is on the same side as the reed switch insert the blade of a screwdriver between the base wall and the bottom of the circuit board pry the circuit board up Do not touch the coils on the circuit board as this may damage the unit Transmitter and Magnet the backplate of the transmitter using the screws provided and replace circuit board The head of the screw must be the circuit board so that the sensor is not out Use flat headed screws only the magnet no more than from the Use the spacers provided Once the and magnet are mounted open and close the to ensure that none of the parts with this movement Only one magnet can used per transmitter COMPLIANCE STATEMENT Changes or modifications not expressly approved by Digital Security Controls Ltd could void your to use this equipment equipment generates and uses radio frequency energy and if not installed and used properly in strict accordance the manufacturer instructions may cause interference to radio and television reception It has been type tested and to comply with the limits for Class B device in accordance with the specifications in Subpart of Part 15 of Rules which are designed to provide reasonable protection against such interference in any residential installation there is no guarantee that interference will not occur in a particular installation If this equipment does cause to television or radio reception which can be determined by turning the equipment off and on the user is to try to correct the interference by one or more of the following measures Re orient the receiving antenna Relocate the alarm control with respect to the receiver Move the alarm control away from the receiver Connect the alarm control into a different outlet so that alarm control and receiver are on different circuits necessary the user should consult the dealer or an experienced radio television technician for additional The user may find the following booklet prepared by the FCC helpful to Identify and Radio Television Interference Problems This booklet is available from the U S Government Printing Washington D C 20402 Stock 004 000 00345 4 Warranty Warranty Warranty Warranty Warranty Security Controls Ltd warrants that for a period of twelve months from the date of purchase product shall be free of defects in material and workmanship under normal use and that in of any breach of such warranty Digital Security Controls Ltd shall at its option repair or the defective equipment upon return of the equipment to its repair depot This warranty only to defects in parts and workmanship and not to damage incurred in shipping or handling damage due to causes beyond control of Digital Security Controls Ltd such as lightning excessive mechanical shock water damage or damage arising out of abuse alteration or improper of the equipment foregoing warranty shall apply only to the original buyer and is and shall be in lieu of any and all warranties whether express or implied and of all other obligations or liabilities on the part of Digital Controls Ltd This warranty contains the entire warranty Digital Security Controls Ltd neither nor authorizes any other person purporting to act on its behalf to modify or to change this nor to assume for it any other warranty or liability concerning this product no event shall Digital Security Controls Ltd be liable for any direct indirect or consequential loss of anticipated profits loss of time or any other losses incurred by the buyer in with the purchase installation or operation or failure of this product Security Controls Ltd recommends that the entire system be completely tested on a regular However despite frequent testing and due to but not limited to criminal tampering or electrical it is possible for this product to fail to perform as expected 2000 Digital Security Controls Ltd Canada cid 127 www dsc com in Canada 29004017 R003 Transmitter INSTRUCTIONS INSTRUCTIONS INSTRUCTIONS INSTRUCTIONS INSTRUCTIONS either notched location on the cover insert the flat blade of a small