DSC WS4938 UM EN NA
File Preview
Click below to download for free
Click below to download for free
File Data
Name | dsc-ws4938-um-en-na-2140395876.pdf |
---|---|
Type | |
Size | 748.87 KB |
Downloads |
Text Preview
Compatibility WS4938 is compatible with the following receivers PC4164 433 v3.00 or greater cid 127 PC5132 433 v4.2X or greater RF5501 433 NT9005 cid 127 RF5108 433 the Batteries normal conditions the batteries can last up to 2 years If battery is low the trouble light on the keypad will turn ON replace the batteries remove the top cover by inserting a into the slot located on the bottom right corner and twist the screw at the center of the board to expose the Replace both batteries with Panasonic CR 2025 lith batteries see diagram NT9005 v1.02 requires that the serial number of the WS4938 be deleted and re enrolled order to restore the low battery The polarity of the battery must be observed as shown in the diagram above Improper han of lithium batteries may result in heat generation explosion or fire which may lead to per injuries Danger of explosion if batteries are installed incorrectly Replace only with the or equivalent type recommended by the manufacturer Keep away from small chil If Batteries are swallowed promptly see a doctor Do not try to recharge these batter Disposal of used batteries must be made in accordance with the waste recovery and regulations in your area Clip Assembly and Mounting 32 120 0 5 93 RH Water Resistant COMPLIANCE STATEMENT device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 This may not cause harmful interference and 2 this device must accept any interference received including inter that may cause undesired operation 160A WS4938 The term IC before the radio certification number only signifies that Industry Canada technical were met and ULC Listed Digital Security Controls Toronto Canada Support 1 800 387 3630 www dsc com in Taiwan Wireless Panic Button Instructions WS4938 Wireless Panic Button was designed to transmit an emer signal from any location within the range of the alarm system if the system is armed or disarmed button is small and lightweight enough to be placed in a shirt pocket tucked away inside a purse It can also be used with the supplied neck or multi functional clip which can connect to your belt car visor or permanently mounted to a convenient location activate press and hold the button for approximately 2 seconds LED located on the top of the unit will light up to confirm a signal been sent Signals will not be received if the button is not within range of the wireless receiver Enrolling and Programming conserve battery power the button comes deactivated To activate sim remove the cover and slide the switch to the ON position to the left device is supervised If the unit is removed from the coverage range a will be indicated on the system If this is not desired the supervisory bit this zone can be disabled on the receiver For UL Listed installations the supervisory bit in the receiver must be following outlines the basic steps for programming and enrolling this on PowerSeries receivers additional options or for other receivers please refer to the specific installation manuals 1 Program Electronic Serial Number ESN 804 subsections 01 32 Zone 1 32 Zone 32 the 6 digit ESN located on the back of the device into the next available zone slot 2 Program Zone Definition 001 004 the selected zone number with appropriate zone type e g 24hr Panic 16 Holdup 12 24hr Medical 15 3 Enable Wireless Zone Attribute 101 132 Option 8 ON wireless zone attribute in corresponding zone attribute section 4 Enable Disable Supervision default is enabled 804 subsections 82 85 Wireless Zone Supervision Zones 1 8 ON Option 1 Zone 01 Supervision Enabled Disabled ON OFF Option 8 Zone 08 Supervision Enabled Disabled Wireless Zone Supervision Zones 9 16 Wireless Zone Supervision Zones 17 24 Wireless Zone Supervision Zones 25 32 WS4938 is compatible with the following receivers PC4164 433 v3.00 or greater cid 127 PC5132 433 v4.2X or greater RF5501 433 NT9005 cid 127 RF5108 433 the Batteries normal conditions the batteries can last up to 2 years If battery is low the trouble light on the keypad will turn ON replace the batteries remove the top cover by inserting a into the slot located on the bottom right corner and twist the screw at the center of the board to expose the Replace both batteries with Panasonic CR 2025 lith batteries see diagram NT9005 v1.02 requires that the serial number of the WS4938 be deleted and re enrolled order to restore the low battery The polarity of the battery must be observed as shown in the diagram above Improper han of lithium batteries may result in heat generation explosion or fire which may lead to per injuries Danger of explosion if batteries are installed incorrectly Replace only with the or equivalent type recommended by the manufacturer Keep away from small chil If Batteries are swallowed promptly see a doctor Do not try to recharge these batter Disposal of used batteries must be made in accordance with the waste recovery and regulations in your area Clip Assembly and Mounting 32 120 0 5 93 RH Water Resistant COMPLIANCE STATEMENT device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 This may not cause harmful interference and 2 this device must accept any interference received including inter that may cause undesired operation 160A WS4938 The term IC before the radio certification number only signifies that Industry Canada technical were met and ULC Listed Digital Security Controls Toronto Canada Support 1 800 387 3630 cid 127 www dsc com in Taiwan Wireless Panic Button Instructions WS4938 Wireless Panic Button was designed to transmit an emer signal from any location within the range of the alarm system if the system is armed or disarmed button is small and lightweight enough to be placed in a shirt pocket tucked away inside a purse It can also be used with the supplied neck or multi functional clip which can connect to your belt car visor or permanently mounted to a convenient location activate press and hold the button for approximately 2 seconds LED located on the top of the unit will light up to confirm a signal been sent Signals will not be received if the button is not within range of the wireless receiver Enrolling and Programming conserve battery power the button comes deactivated To activate sim remove the cover and slide the switch to the ON position to the left device is supervised If the unit is removed from the coverage range a will be indicated on the system If this is not desired the supervisory bit this zone can be disabled on the receiver For UL Listed installations the supervisory bit in the receiver must be following outlines the basic steps for programming and enrolling this on PowerSeries receivers additional options or for other receivers please refer to the specific installation manuals 1 Program Electronic Serial Number ESN 804 subsections 01 32 Zone 1 32 Zone 32 the 6 digit ESN located on the back of the device into the next available zone slot 2 Program Zone Definition 001 004 the selected zone number with appropriate zone type e g 24hr Panic 16 Holdup 12 24hr Medical 15 3 Enable Wireless Zone Attribute 101 132 Option 8 ON wireless zone attribute in corresponding zone attribute section 4 Enable Disable Supervision default is enabled 804 subsections 82 85 Wireless Zone Supervision Zones 1 8 ON Option 1 Zone 01 Supervision Enabled Disabled ON OFF Option 8 Zone 08 Supervision Enabled Disabled Wireless Zone Supervision Zones 9 16 Wireless Zone Supervision Zones 17 24 Wireless Zone Supervision Zones 25 32