DSC WS8904 Installation Instructions (English)

WS8904 Installation Instructions intended area Refer Installation Manual shall be used in conjunction with the Installation of the DSC wireless receiver and control panel with which this is intended to be used WS8904 motion detector should be located so that it provides coverage of Changing Motion Lenses below for information on the four lenses available for the Motion Detector the Detector locating motion detectors observe the following for Wall to Wall and Curtain Lenses the mounting height should be 6 10 ft 2 3m the floor The nominal mounting height is 7.5 ft 2.3m For the Pet Lens only the mounting height should be 4 5 ft 1.2 1.5m from the the following to avoid false alarms Do not aim the detector at a stairwell to which a pet has access Do not place furniture or objects higher than 3ft 0.9m which a pet climb onto e g a cat on a couch closer than 6ft 1.8m from the Mount the detector flat on a wall or in a corner Do not angle it or use mounting brackets with this detector when it is in conjunction with pets Do not aim the detector at reflective surfaces such as mirrors or as this may distort the coverage pattern or reflect sunlight onto the detector Avoid locations that are subject to direct high air flow such as near an duct outlet Do not locate the detector near sources of moisture such as steam or Do not limit the coverage by large obstructions in the detection area as plants or cabinets indoor use only non hazardous locations supplied with the Wall to Wall No detector should be mounted without first performing a module test to determine that it is in range of the wireless receiver See Placement Test instructions in the Instruction Sheet for your receiver in the Installation Manual for your system a location has been selected remove the plastic from the mounting and locate the backplate on the wall and mark screw locations It is that wall anchors be used for all screw locations Secure the to the wall and then secure the enrolled detector to its Use only backplates marked as Using any other will result in the tamper switch being broken a WS8904 the back of the PIR housing there will be a six digit number Motion Detector Lenses motion detector lenses are available for the WS8904 motion detector The charts the following page illustrate the range and coverage patterns of each change the lens first open the motion detector by removing the screw the bottom of the battery compartment With the screw removed pull back of the detector away from the front case Remove the lens holder pressing down on the top of the holder and pulling the holder away the case When installing the new lens ensure the grooved surface the interior of the case and the notches on the lens face the bottom the case Replace the lens holder by snapping it back into place the motion detector by first engaging the clips on the bottom the case Close the case and then secure the case with the screw in the of the battery compartment the Motion Detector Sensitivity motion detector features Fast and Slow detection modes which are on jumper JP1 In a normal operating environment the fast setting the best detection certain environments where rapid air movement heaters and other present problems use Slow detection mode to stabilize the Jumper is located at the top right under the battery of the circuit board To change the setting from Fast to Slow move jumper over one pin as shown in Figure 4 Traffic Shutdown Mode prolong battery life the motion detector uses a feature called High Shutdown When motion is detected the device will transmit to the and will then shut down for three minutes If motion is detected during the shutdown time the unit will not transmit the event to receiver The detector will thus remain in the shutdown mode until minutes after the first motion detected was transmitted The will transmit detected motion every three minutes The High Shutdown Mode affects testing the motion detector in two ways When performing the module placement test the unit must be by removing the unit from the backplate and replacing it placement test cannot be performed by creating motion in front the device When performing a system test the unit must be left idle for three before testing can be performed Once three minutes has create motion in front of the detector to see if the device is detecting motion and transmitting to the receiver Detector Transmission Delay motion detector transmission is always delayed by 6 seconds This is to prevent false alarms caused by a motion sensor transmitting a delay zone has a chance to report This 6 second delay cannot be or disabled Test Mode motion detector has a walk test mode which will activate an LED for purposes During normal operation the LED will not turn on To the detector in walk test mode create a tamper by removing the from its backplate and then replacing it Each time the detector motion will flash the red LED Six seconds after motion is the detector will send a signal to the receiver The detector will in walk test mode until it has sent 10 transmissions To test for catch of humans create motion in the entire area where coverage desired by walking perpendicular to the lens pattern Should the be incomplete readjust or relocate the detector The Walk Test Mode will override the High Traffic Shutdown Mode the installer is activating the walk test mode or replacing a then he must create 10 alarm transmissions before leaving the because the indicator is still working and will not stop working until alarm transmissions have been sent Installation Fig 3 system is designed to work with the consumer grade batteries Lithium EL123AP Panasonic Lithium CR123A or Duracell Ultra 123 Do not install any other type The reliability of the system depends on its batteries and name or generic batteries may not provide the best quality and dependability of another type of battery may present a risk of fire or explosion Use a fresh battery Most batteries have a before date printed their packaging or on the batteries themselves Buy batteries that a before date of two years or more from your purchase the motion detector from its mounting plate by holding the by its sides and pushing up Remove the battery cover see 3 Remove the old battery and install new battery Place the cover back on Secure the battery cover with the small screw provided the sensor on its mounting plate making sure it snaps into After the battery is installed the detector will take 60 seconds warm up During this time the LED will flash slowly The polarity of the battery must be observed see Figure 3 handling of lithium batteries may result in heat generation or fire which may lead to personal injuries DANGER OF EXPLOSION IF BATTERIES ARE INSTALLED REPLACE ONLY WITH THE SAME OR EQUIVALENT TYPE BY THE MANUFACTURER away from small children If batteries are swallowed promptly see a Do not try to recharge these batteries Disposal of used batteries be made in accordance with the waste recovery and recycling in your area The battery may explode if mistreated Do not dispose in fire recharge or disassemble Operating Temperature 10 to 55 14 131 Operating Humidity 5 to 93 RH non cond Life 9 years typical usage in room temperature Nominal Voltage is 3V Low Battery Trouble indication is at 2.2V Compatible Receivers RF5132 868 RFK55xx 868 SCW9045 9047 868 PC9155 868 Pattern Wall to Wall Lens Standard For Installations compliant with EN50131 Standard the range for the Fast Setting is x 10.3m The Slow setting shall not be Setting 15.2m 18.3m 50 60 Setting 10.6m 18.3m 35 33 26 19.7 13 6.6 6.6 13 19.7 26 33 Corridor Lens optional 3.2 m 80 10,5 Curtain Lens optional 1.3 m 50 4,4 Pet Alley Lens optional 18.3 m 50 60 1 Detector Backplate For installations compliant with