DSC WS8920 ENG FRE SPA POR IT
File Preview
Click below to download for free
Click below to download for free
File Data
Name | dsc-ws8920-eng-fre-spa-por-it-3786902145.pdf |
---|---|
Type | |
Size | 4.38 MB |
Downloads |
Text Preview
WS8920 v1.0 Instructions Instructions d Instrucciones de Instru de Instala Istruzioni di installazione Use these instructions in conjunction with the installation manual of the alarm panel with which this is intended to be used READ and SAVE These Instructions Follow All WARNINGS AND INSTRUCTIONS specified this document and or on the equipment INSTRUCTIONS for WS8920 WIRELESS REPEATER equipment WS8920 WIRELESS REPEATER 1.0 shall be installed and used within an that provides the pollution degree max 2 and overvoltages category II NON LOCATIONS indoor only The equipment is FIXED and DIRECT PLUG IN powered the mains it is designed to be installed by Service Persons only Service Person is defined as a having the appropriate technical training and experience necessary to be aware of hazards to that person may be exposed in performing a task and of measures to minimize the risks to that or other persons The equipment is installed in a FIRE ENCLOSURE If during the installation a knockout is removed it is the installer responsibility to ensure that same degree of protection for the enclosure is provided by the use of bushings fittings etc The enclosure must be secured to the building structure before operation Internal wiring must be routed in a manner that prevents Excessive strain on wire and on terminal connections Loosening of terminal and connections Damage of conductor insulation The end user and or installer are responsible for ensuring that the disposal of the used batteries pack is made according to the waste recovery and recycling regulations applicable to intended market When using equipment connected to the MAINS always follow basic safety instructions to the SAFETY INSTRUCTIONS provided with this product save them for future reference the end user regarding the safety precautions that shall be observed when operating this equipment precautions required during installation NEVER install this equipment during a lightning storm NEVER touch uninsulated wires or terminals unless the direct plug in transformer has been dis Ensure that cables are positioned so that accidents cannot occur Connected cables must NOT be to excessive mechanical strain Use only the power supply provided with this equipment Use of unauthorized power supplies The AC socket outlet powering the equipment shall be located near the equipment and shall be damage the WS8920 accessible Do NOT locate this product where persons will walk on the secondary circuit cable s Do NOT use extension cords to plug in the power supply of this equipment AVOID setting up the equipment near heaters air conditioners ventilators and or refrigerators Do NOT connect to electrical outlets on the same circuit as large appliances Do NOT select a place exposed to direct sunlight excessive heat moisture vapors chemicals or Do NOT install this Equipment near water e g bath tub wash bowl kitchen laundry sink in a basement or near swimming pool etc Do NOT install this equipment and its accessories in areas where there is a risk of explosion Do NOT connect this equipment to electrical outlets controlled by wall switches or automatic avoid interference sources EQUIPMENT HAS NO MAINS ON OFF SWITCH THE PLUG OF THE DIRECT PLUG IN POWER IS INTENDED TO SERVE AS THE DISCONNECTING DEVICE IF THE EQUIPMENT MUST QUICKLY DISCONNECTED IT IS IMPERATIVE THAT ACCESS TO THE MAINS PLUG AND MAINS SOCKET OUTLET IS NEVER OBSTRUCTED of Contents Table des mati Indice dei contenuti Instructions 2 d 10 de Instalaci de Instala 34 di installazione 46 WS8920 is compatible with the following DSC wireless devices Window Contact Detector Panel Receiver EU Detector Key Detector Pendant WS8920 is not compatible with 2 way devices Temperature range 10 to 55 14 Humidity Max 5 93 R H non condensing Battery type Rechargeable Ni MH 4.8V 2.1 AH Listed as an LPS Replace battery every 3 5 Battery backup time 24 hours Battery charging rate 80 within 24 hours Battery charging current 170mA Operating frequency 868.35 MHz Dimensions H6.96 W4.47 D1.33 in W11.35 D3.38 cm Weight 77 lb 35kg requirements Class II power limited transformer fused 120VAC 60Hz 0.2A International Market Acceptable to the local authorities 230VAC 50Hz 0.1A International Market Acceptable to the local authorities 16VAC 18VAC 20VA following plug in transformers shall be used 120V 16.5V 20VA CE approved 230V 16.5V 20VA allowed wire run distances Feet Meters WS8920 is a wireless repeater designed to extend the range of DSC one way wireless and to improve signal quality between the transmitter and receiver Use the to remedy transmission problems caused by excessive noise or other interference or long distances between devices and receivers The maximum recommended number of per alarm system is 4 enrolled WS8920 occupies a zone slot The WS8920 does not increase the number of wireless zones This is determined by the control panel wireless receiver Only zones repeat functionality need to be enrolled on the WS8920 Ensure these zones are enrolled on the WS8920 and the receiver control panel your package includes the following One WS8920 rechargeable Ni MH battery included One direct plug in transformer Not included in all configurations Mounting hardware pack including plastic wall plugs and screws Installation instructions and Indicators WS8920 has three LEDs on the front The of these LEDs is different when in operational mode cover on than when Installer mode cover off See the table for descriptions of LED functionality wall tamper must be closed for the LEDs operate 1 LED Indicators 1 LED Definitions Normal Mode cover on On AC present No AC battery good No AC and dead battery On Battery not connected Battery good if AC on Low battery On RF jam present No RF jam Installer Mode cover off 1 flash Enrolled Placement test active Flashing Zone not enrolled On Repeater placement test Repeater placement test Sporadic interference or valid packets detected WS8920 includes a Programming button to place it into Enroll Placement modes 4 position DIP switch is also provided to set following options 2 DIP Switch Settings tamper enabled Wall tamper Jam notification sent to receiver with RF5132 SCW and PC9155 installations 1 WS8920 Jam sent receiver with receivers installations Multiple default for all switches is ON 2 Internal Controls Switch the WS8920 in the following order When enrolling and placement testing the WS8920 with the alarm panel refer to the control panel installation instructions for the appropriate programming sections 1 Temporarily Mounting the WS8920 a suitable location for the WS8920 Use the following list as a guide Locate device near a power outlet Location should be free from vibration and shock Mount on a flat stable surface Ideal location is mid way between the wireless transmitter