DSC WT4901 Installation Manual

WT4901 WT8901 v1.0 Instructions Instructions d Instrucciones de instalaci Instru de Instala di installazione Installatiehandleiding Installationsguide Installasjonsinstruksjoner Pokyny k instalaci Instrukcja instalacji Asennusohjeet Fran Espa Italiano Nederlands Norsk Dansk Suomi 900 7529 R00 6 Two Way Wireless Siren Installation Instructions this installation sheet along with the associated alarm system installation for installation instructions and programming details All instructions within that manual must be observed WT4901 WT8901 is a two way wireless indoor siren It sounds an alarm condi received via DSC wireless protocol from a compatible two way enabled security e g PC9155 After the WT4901 WT8901 is enrolled on the security panel it capable of receiving commands from the panel for sounding alarms and communi any required response such as system status The siren is capable of sounding alarm cadences e g continuous burglary pulsating fire or temporal three bell squawks and buzzer tones to suit the type of command it receives The provides a supervisory signal to the security panel to ensure its wireless communication capability is functioning In addition it monitors case and wall tamper switch states and the battery state In the event of a low or a tamper activation the WT4901 WT8901 transmits the appropriate to the security panel and if applicable provides an audible indication that system event has occurred Up to four WT4901 WT8901 sirens can be enrolled and supervised by the same security panel as separate units Temperature 10 to 55 14 to 131 range for UL ULC 0 to 49 Humidity 0 to 93 R H non condensing Frequency 433.92MHz 868 MHz WT8901 only 4 AA 1.5V Alkaline Energizer E91 Life 2 years typical usage Battery Level 4.2 V pre determined Signals Output Level 85dB 3m high volume Signals Output Level 65dB 3m medium volume control panels PC9155 433 868 PC9155D 433 868 PC9155G 433 868 for WT8901 only Only model WT4901 is UL and ULC listed of the Box WT8901 Installation sheet hardware pack 3 screws and 3 plastic 4 AA batteries Wireless Siren Enrollment WT4901 WT8901 serial number is only used when the indoor siren is enrolled powered up Enrolling the WT4901 WT8901 permits it to communicate with control panel The installer can activate the indoor siren by Quick Enrollment Serial Number Programming see below NOTE Make sure the Keypad is set up activating the indoor siren Enrollment Enter the enrollment mode through installer programming see section 898 in alarm system installation guide Power up the indoor siren If it is already powered up press and hold the test for 2 seconds the siren will beep The indoor siren sends a request to the security panel to enroll on the system The Keypad displays the electronic serial number which must be confirmed pressing If the electronic serial number is incorrect press and this step Select the module number that the device should be enrolled as Number The electronic serial number is an 8 digit alphanumeric number on a sticker on the wireless device Repeat starting from step 2 to enroll each additional indoor siren Number Programming Enter the enrollment mode through installer programming see section 804 in alarm system installation guide Select the module number that the device will be enrolled as See sections for sirens Enter the serial number using the Keypad Test a placement test to ensure there is sufficient signal strength for proper between the security panel and the siren location Place the security panel into placement test see section 906 Start the test by tampering and restoring the siren being tested or pressing and the Test button for 2 seconds the siren will give a beep The siren will respond with one beep if the location is or three beeps if siren is at a location Installation indoor siren is mounted to a flat surface such as drywall or any variety of surfaces with the supplied hardware When mounting the WT4901 WT8901 on drywall the use of the plastic is mandatory NOTE Do not mount over a single gang electrical box Open the WT4901 WT8901 by inserting a screwdriver into the slots and gently on the front cover until it separates from the backplate If the batteries are not installed install them as shown in the polarity indicated the engraving Position the backplate on a flat mounting surface and mark this location Secure the backplate to the mounting surface with all the screws provided Hinge the front cover to the backplate carefully to correctly align it with the switch then snap it onto the backplate The wall tamper switch must closed when the indoor siren is mounted Mounting Requirements USA ceiling heights allow wall mounted appliances shall have their tops above the floors at heights of not less than 2.30 m 90 in and below the finished at distances of not less than 150 mm 6 in Mounting heights other than shall be permitted by the authority having jurisdiction provided the sound level requirements are met Button test button activates the local siren for 4 seconds Press and hold the siren test located at the front of the WT4901 WT8901 for 5 seconds to verify the siren is functioning If it is the siren will sound at medium volume for 2 followed by 2 seconds at full volume The WT4901 WT8901 does not have to be enrolled on a system to perform this test Replacement security panel will indicate when the batteries are low and require replacement To which siren has a low battery press and hold the test button for 5 seconds If the sounds for 4 seconds the batteries are good If the siren doesn sound the batteries low After removing the batteries wait 30 seconds before inserting replacement batter Energizer 1.5V AA alkaline batteries can be used REPLACE ONLY WITH THE TYPE BY THE MANUFACTURER Open the front cover and install the as shown in the polarity indicated by the engraving If the batteries are installed in the reverse polarity the indoor siren will not work Under typical use the is capable of operating on battery power alone without having to change batteries for a minimum of two years Do not try to recharge these batteries of used batteries must be made in accordance with the waste and recycling regulations in your area Siren Front Cover Siren Backplate 2 Button 4 AA Alkaline Hole for removing front cover and Testing necessary WT4901 WT8901 options can be set up to suit desired system By means of the keypad interface the installer has access to the siren menus supported by the main panel e g wireless siren options see below siren enrollment and placement test activation menu Do Not set the WT4901 to follow Entry Exit delay for SIA CP 01 com installations Section Alarm Disabled Buzzer Notification Dis Alarm Enabled Buzzer Notification Door Chime Enabled Trouble Beeps Enabled Bell Squawks Enabled For Future Use Buzzer Alarms follow BTO Siren Tamper Enabled Door Chime Disabled Trouble Beeps Disabled Bell Squawks Disabled For Future Use Buzzer Alarms follows Condition Siren Tamper Disabled Tamper does not Acti Siren Strobe Pre Alarm Signal Dis to cid 137 8 For Future Use Sounder Tamper Activates Siren Pre Alarm Signal Enabled to cid 137 8 For Future Use Warranty Security Controls warrants that for a period of 12 months the date of purchase the product shall be free of defects in and workmanship under normal use and that in fulfilment any breach of such warranty Digital Security Controls shall at its repair or replace the defective equipment upon return of equipment to its repair depot This warranty applies o