DSC WT4989 8989 - R004 - User Manual - EN DU IT FR

File Preview
File Preview
Click below to download for free

File Data

Name dsc-wt4989-8989-r004-user-manual-en-du-it-fr-3548267019.pdf
Type PDF
Size 10.07 MB
Downloads

Text Preview

WT4989 WT8989 Two Way Wire Key Operating Instructions ICON WT4989 WT8989 is a five two way wireless key an LCD icon display and a buzzer The LCD icons to show the system when the Status Request is pressed In addition buzzer will to indi that a button was pressed that the wireless key has sent command to the control panel The wireless key communicates compatible wireless receivers to allow you to arm disarm and your requested actions as well as other keypad functions the convenience of wireless portability To activate press and a button for approximately 1 second device contains no user serviceable components EN50131 GRADE2 CLASS II EN50131 3 EN50131 6 TYPE C Some key functions require a 3 second press LCD backlighting and antenna icon turn on and the buzzer once indicating that a button has been pressed These also confirm that a signal has been sent to the control receiver Frequency 433.92 MHz 868 MHz WT8989 only CR2032 6V 2 3V Lithium Panasonic Energizer Life Battery Level LxWxH 75mm x 40mm x 16mm Temp Receivers PC9155 433 868 PC9155D 433 868 to 55 R H non condensing years under typical use pre determined PC9155G 433 868 868 for WT4989 is UL ULC listed This equipment shall be used in an environment provides the pollution degree max 2 in NON HAZARD locations ONLY Button Functions Request Press this button for 1 second to view the panel system status via the LCD icons Press and hold both at the same time for 3 to lock the keys To unlock the keys press both buttons for 3 Note pressing the Panic button automatically unlocks keys and transmits provided there is a 3 second delay on the Panic This is the case regardless of the state of the Keylock Stay Arming Press to arm your system in Stay mode All zones are active while Stay Away and Night zones are Away Arming Press to arm your system in Away mode Disarm Press to disarm your system Panic Alarm Press and hold for 3 seconds to create a alarm Output 1 Press both at the same to activate the assigned output Output 2 Press both at the same time activate the assigned output Default Serial Number Press both at same time to send the default serial number This allows you to the wireless key e g after a default of the receiver the key is enrolled on WT4989 WT8989 options are available in order to pro the best possible combination to suit specific needs For UL installations refer to the relevant control panel Installation to Enroll the WT4989 WT8989 section describes how to set up and program your wireless key following outlines the basic steps for programming and enroll this device on 2 way wireless compatible receivers For addi options or for other receivers please refer to the specific Installation Manual The flashing is attempting to enroll on a system 1 Enroll the Device WT4989 WT8989 is enrolled by Quick Enrollment or Serial Programming Enrollment Enter 8 Installers Code 898 through installer pro icon indicates the WT4989 Press any key on the wireless device to enroll it The keypad will display the 8 digit ESN confirm by Enter the Key slot 1 16 Repeat from Step 2 to enroll additional wireless keys Program Electronic Serial Number ESN Enter 8 Installers Code 804 subsections 101 Enter the 8 digit ESN located on the back of the unit Key 1 16 wireless key is provided with a unique serial number hard at the factory consisting of 8 hexadecimal digits The total of possible combinations is 16.7 million The end user not change this number only the enrolled serial numbers 2 Program Function Buttons 804 subsections 141 156 additional programmable options refer to the control Installation Manual Button 1 Stay Arming Button 2 Away Arming Button 3 Disarm Button 4 Panic Buttons 1 2 Command Output 1 Buttons 1 3 Command Output 2 Programming Mode the to Program the WT4989 WT8989 the programming will affect operation This should be done the installer To program WT4989 WT8989 options 1 Press and all 4 buttons simultaneously for 3 5 seconds until the appears and begins to flash Programming mode lasts 5 seconds Choose a WT4989 WT8989 Local Programming Option from the To restore the default values repeat Steps 1 and 2 Program this Option Do This the key beeps the 3 sec delay on key key 3 key 4 Keylock off the backlighting the the the the the key key key key For UL Listed installations the Bell feature of the control panel must be enabled 3 second delay on the Panic key must be enabled Bell Squawk must be audible from outside the prem Arming Disarming confirmations must be indicated the wireless key LCD Refer to the control panel Manual for details Clip multi function clip provided can clip to a sun visor or it can clip to a belt Panel System Status table below summarizes the status that can be shown by the LCD S Steady F Flashing SYSTEM STATUS S System Trouble S Disarmed S Away Armed S Stay Armed S Night Armed S Low Battery F Critical Low Battery F 9 Armed Away F 9 Armed Stay F Keylock Enable S Alarm in Memory F Active Alarm F 9 Armed Night Replacement the battery is low the battery icon the LCD illuminates If the battery reached a critically low state the icon flashes Replace batteries icon is displayed To the the batteries remove the bot cover by inserting a coin into the slot located on the center and twist Replace both batteries with Panasonic or lithium 3V batteries CR 2032 only NOTE The of the battery must be observed as shown in the dia REPLACE ONLY WITH THE SAME TYPE AS RECOM BY THE MANUFACTURER Keep away from small If batteries are swallowed promptly see a doctor Do try to recharge these batteries Disposal of used batteries be made in accordance with the waste recovery and recy regulations in your area Draadloze WT4989 WT8989 is een vijf knoppen een lcd scherm pictogrammen en een zoemer De lichten op om de weer geven de knop Statusverzoek ingedrukt De zoemer piept aan te geven dat er een knop ingedrukt of dat er een opdracht is verzonden aan het De draadloze afstandsbediening communiceert met draadloze ontvangers U kunt het alarm ermee in en bevestiging krijgen van gevraagde acties en overige uitvoeren dat alles met het gemak van Houd om een knop te activeren deze ongeveer 1 ingedrukt zijn geen onderdelen aanwezig in dit apparaat die door de gebruiker worden onderhouden EN50131 1 GRADE2 CLASS II EN50131 6 TYPE C voor sommige functies moet een knop 3 seconden worden ingedrukt verlichting van het lcd scherm en het antennepictogram aan en de zoemer piept een keer om aan te geven dat er een is ingedrukt Hiermee wordt ook bevestigd dat een signaal is naar de ontvanger van het bedieningspaneel MHz 868 MHz alleen WT8989 CR2032 3 V lithium Panasonic van batterijen 3 jaar bij typisch gebruik bijna leeg L x B x H 93 niet condenserend ontvangers PC9155 433 868 PC9155D 433 868 vooraf bepaald mm x 40 mm x 16 mm g tot 55 PC9155G 433 868 868 alleen deze apparatuur moet worden gebruikt in een met maximale NIET GEVAARLIJKE locaties standaardfuncties van de knoppen 2 Statusverzoek Houd deze knop 1 seconde ingedrukt om de van het bedieningpaneel te bek

Related Files