DSC WT4989 WT8989 Operating Instructions -ENG GER S-CHI DUT

WT4989 WT8989 Two Way Wireless Operating Instructions ICON WT4989 WT8989 is a five two way wireless key an LCD icon display and a buzzer The LCD icons to show the system when the Status Request is pressed In addition buzzer will to indi that a button was pressed that the wireless key has sent a command to the control panel wireless key communicates with compatible wireless receivers allow you to arm disarm and confirm your requested actions well as other keypad functions with the convenience of wireless To activate press and hold a button for approximately second device contains no user serviceable components Some key functions require a 3 second press LCD backlighting and antenna icon turn on and the buzzer once indicating that a button has been pressed These also confirm that a signal has been sent to the control receiver Frequency CR2032 Life Battery Level L Temp MHz 868 MHz WT8989 only 2 3V Lithium Panasonic Energizer years under typical use pre determined to 55 14 to 131 0 to 49 32 to 120.2 R H non condensing Receivers PC9155 433 868 PC9155D 433 868 PC9155G 433 868 868 for WT4989 is UL ULC listed This equipment shall be used in an envi that provides the pollution degree max 2 in locations ONLY Button Functions Request Press this button for 1 second to view the panel system status via the LCD icons Press and hold both at the same time for 3 757 4R0 04 to lock the keys To unlock the keys press both buttons for 3 Note pressing the Panic button automatically unlocks keys and transmits provided there is a 3 second delay on the Panic This is the case regardless of the state of the Keylock Stay Arming Press to arm your system in Stay mode All zones are active while Stay Away and Night zones are Away Arming Press to arm your system in Away mode Disarm Press to disarm your system Panic Alarm Press and hold for 3 seconds to create a alarm Output 1 Press both at the same to activate the assigned output Output 2 Press both at the same time activate the assigned output Default Serial Number Press both at same time to send the default serial number This allows you to the wireless key e g after a default of the receiver the key is enrolled on WT4989 WT8989 options are available in order to program best possible combination to suit specific needs For UL listed refer to the relevant control panel Installation Manual to Enroll the WT4989 WT8989 section describes how to set up and program your wireless key following outlines the basic steps for programming and enroll this device on 2 way wireless compatible receivers For addi options or for other receivers please refer to the specific Installation Manual The flashing is attempting to enroll on a system 1 Enroll the Device WT4989 WT8989 is enrolled by Quick Enrollment or Serial Programming Enrollment Enter 8 Installers Code 898 through installer program icon indicates the WT4989 Press any key on the wireless device to enroll it The keypad will display the 8 digit ESN confirm by pressing Enter the Key slot 1 16 Repeat from Step 2 to enroll additional wireless keys Program Electronic Serial Number ESN Enter 8 Installers Code 804 subsections 101 116 Enter the 8 digit ESN located on the back of the unit Key 1 16 wireless key is provided with a unique serial number hard at the factory consisting of 8 hexadecimal digits The total of possible combinations is 16.7 million The end user can change this number only the enrolled serial numbers 2 Program Function Buttons 804 subsections 141 156 additional programmable options refer to the control panel Manual Button 1 Stay Arming Button 2 Away Arming Button 3 Disarm Button 4 Panic Buttons 1 2 Command Output 1 Buttons 1 3 Command Output 2 Programming Mode key the to Program the WT4989 WT8989 the programming will affect operation This should be done by installer To program WT4989 WT8989 options 1 Press and hold 4 buttons simultaneously for 3 5 seconds until the icon and begins to flash Programming mode lasts 5 seconds 2 a WT4989 WT8989 Local Programming Option from the table restore the default values repeat Steps 1 and 2 Program this Option Do This the key the beeps the 3 sec delay on key key 3 key 4 Keylock off the backlighting For UL listed installations the Bell feature of the control panel must be enabled 3 second delay on the Panic key must be enabled Bell Squawk must be audible from outside the prem the the the the key key key Arming Disarming confirmations must be indicated the wireless key LCD Refer to the control panel Manual for details Clip multi function clip provided can clip to a sun visor or it can clip to a belt Panel System Status table below summarizes the status that can be shown by the LCD S Steady F Flashing SYSTEM STATUS S System Trouble S Disarmed S Away Armed S Stay Armed S Night Armed S Low Battery F Critical Low Battery F 9 Armed Away F 9 Armed Stay F Keylock Enable S Alarm in Memory F Active Alarm F 9 Armed Night Replacement the battery is low the battery icon the LCD illuminates If the battery reached a critically low state the icon flashes Replace batteries the icon is displayed To the batteries remove the bot cover by inserting a coin into the slot located on the center and twist Replace both batteries with Panasonic or Ener lithium 3V 6V batteries CR 2032 only NOTE The of the battery must be observed as shown the diagram REPLACE ONLY WITH THE SAME TYPE RECOMMENDED BY THE MANUFACTURER Keep from small children If batteries are swal promptly see a doctor Do not try to recharge batteries Disposal of used batteries must be in accordance with the waste recovery and regulations in your area Compliance Statement Changes or modifications not expressly approved by Digital Controls could void your authority to use this equipment This has been tested and found to comply with the limits for a B digital device pursuant to Part 15 of the FCC Rules Operation is to the following two conditions 1 This device may not cause interference and 2 this device must accept any interference including interference that may cause undesired operation 160A WT4989 The term before the radio certification number signifies that Industry Canada technical specifications were met Class B digital apparatus complies with Canadian ICES 003 Cet appareil de la classe B est conforme la norme NMB 003 du Canada Warranty Security Controls warrants that for a period of 12 months from the date purchase the product shall be free of defects in materials and workmanship normal use and that in fulfilment of any breach of such warranty Digital Controls shall at its option repair or replace the defective equipment return of the equipment to its repair depot This warranty applies only to in parts and workmanship and not to damage incurred in shipping or or damage due to causes beyond the control of Digital Security Con such as lightning excessive voltage mechanical shock water damage or arising out of abuse alteration or improper application of the equip The foregoing warranty shall apply only to the original buyer and is and be in lieu of any and all other warranties whether expressed or implied and all other obligations or liabilities on the part of Digital Security Controls Security Controls neither assumes responsibility for nor authorizes any person purporting to act on its behalf to modify or to change this warranty to assume for it any other warranty or liability concerning this product In no shall Digital Security Controls be liable for any direct indirect or conse