Edwards 102 Light Source Instructions

Series Triliptical Stackable Beacon Lighting Light Sources Installation Sheet the appropriate light source into board grooves bottom of lens ensuring that the four prongs on the board are aligned with the plug located in the back the lens assembly When using LED light sources ensure that the color the LED light source and the color of the lens assembly To prevent leakage ensure the magnifier ring on lens cover and the magnifier ring on the lens module are Figure 1 Place the lens module cover on the front of the lens and secure using two captive screws Repeat steps a through c for any remaining modules to 5 Once the last module has been assembled place the on top and secure the cap with the captive screw Apply power to the unit and verify proper operation For further installation details see the instructions with the lens modules P N 3100700 or the supplied with the base P N 3100669 To prevent electrical shock disconnect power to modules Wait 5 minutes for stored energy in strobe to dissipate before working on unit Source Replacement Loosen captive screws and remove cover of affected lens Remove the light source assembly from the lens module new light source assembly ensuring that the four on the PC board are aligned with the plug located the back of the lens module To prevent leakage ensure the magnifier ring on lens cover and the magnifier ring on the lens module are Figure 1 Replace lens cover and secure using two captive screws Operation Edwards Triliptical Stackable Beacon Lighting System is a audible visual signaling device that can contain up to 5 modules and either a single or multiple tone module in a stack components of the Triliptical Stackable Beacon Lighting are UL and cUL listed subassemblies The units assembled are UL and cUL listed for indoor and outdoor enclosures are NEMA 3R 4X and IP65 rated Each light module contains a removable cover to allow for easy The light module cover features a molded in gasket dust tight reliability To prevent electrical shock do not connect power instructed to do so must be in accordance with local codes Assemble the stackable beacon lighting system Figure 1 Loosen captive screws and remove cover of affected module 2010 UTC Fire Security All rights reserved 2 3100701 REV 3 ISS 09AUG10 lens surfaces should be periodically dusted and cleaned a dry soft clean cloth to maintain optimum light visibility If the outside of the lens may be cleaned with water a mild detergent on a well rung out soft clean cloth 1 Assembling the stackable beacon lighting system Light Modules 102LS SINH 102LS SIN 102LS FINH 102LS FIN 102LS ST 102LS SLED 102LS FLED Lamp 102LS SINH 102LS SIN 102LS FINH 102LS FIN shown are for a stackable indicator with 5 light modules non halogen lamp Ind Trade 303 may be used in place of the lamp VAC N5 A A A A A A A VDC G1 A A A A A A A Trade 303 Trade 303 1 Lamp Life Hours Source nominal operating voltage lamp life based on manufacturer calculated lamp life fpm and 50 duty cycle tube life operating power to 75 efficiency module 3 Joule strobe module flashing 9W halogen module flashing 12W halogen module flashing 10W incandescent module steady on 9W halogen module steady on 12W halogen module steady on 10W incandescent 2 Part numbers Number lens module color A amber orange B blue C clear G green R red Y yellow lens and LED module color A amber orange B blue G green R red NOTE LED light sources must be used with the color lens module e g a blue LED light source 102LS must be used with a blue lens 102LM B Extension Pipe 4 in Extension Pipe 10 in Extension Pipe 15 in module steady on LED module flashing LED information Signaling Edwards A Division of UTC Fire Security Corporation Inc Town Center Parkway Bradenton FL USA information contact information see www edwardssignaling com 2 3100701 REV 3 ISS 09AUG10 3100701 OFFSET INSTRUCTIONS FOR 102 SERIES STACKABLE STATUS INDICATOR LIGHT SOURCES 8 1 2 x 11 SHEET PRINTED BOTH SIDES FOLD TWO TIMES TO SHOWN ON DETAIL WITH PART NUMBER ON THE OUTSIDE STANDARD WHITE OFFSET STOCK TO BE BLACK ON WHITE BACKGROUND MECHANICALS HAVE ALREADY BEEN REDUCED TO ACTUAL SIZE MECHANICALS TO WRITING SIGNALING WOODFORD AVENUE CT 06062 09 C1917 03 3100700 BY DVG