Edwards 109 Series Installation Instructions

Installation Instructions for 109 Series Star BurstTM Visual Indicator 109 Series Visual Indicator is a UL and cUL listed signaling in a NEMA 4X and IP65 rated enclosure The modules be panel mounted or conduit mounted visual indicator is normally steady on and with a contact the light will flash The unit is set for the Rapid Star Burst flash but with a simple jumper change can output a 65 per minute signal visual indicators are available in red blue green amber or DC DC DC DC DC 50 60 Hz 50 60 Hz 50 60 Hz 50 60 Hz 50 60 Hz A A A A A A A A A A prevent electrical shock ensure that power is off before installing the signal Mounting Figure 1 Thread the 18 45.7 cm signal wire leads through either 13mm or 3 4 19 mm conduit into an approved conduit box Product is supplied with a double threaded 1 2 internal and 3 4 19mm external conduit hub Using wire nuts not supplied connect the signal wire leads shown in Figure 1 Polarity must be observed on DC models avoid risk of injury install lens before energizing unit avoid the risk of injury do not remove or insert source when unit is energized Thread the conduit onto the base of the signal Turn on power and verify that the signal operates properly Mounting Figure 2 The integrity of the outdoor NEMA 4X and IP65 rating on panel assembly at the interface with the 109 Series Visual relies on the construction and configuration details of mounting surface Installer should evaluate Place the mounting gasket supplied over the hole in the and route the signal wires through the gasket and the in the panel the base through the hole in the panel and screw the nut supplied with the raised locking edge facing mounting surface onto the base to secure the beacon Using wire nuts not supplied connect the signal wire leads shown in Figure 1 or 2 Polarity must be observed on DC Connect the Red DC models or Black AC models wire hot Connect the Black DC models or White AC models to steady on applications trim the yellow wire short cap using a wire nut not supplied For either Star flicker flash or standard 65 fpm flash connect the wire to hot to activate On AC models only the yellow can be connected hot negative or ground to activate the Star Burst flash or standard 65 fpm flash Turn on power and verify that the signal operates properly Installation 109 Series Visual Indicator is supplied with a default setting Star Burst flicker flash If a standard flash rate of 65 fpm is open the unit by removing 4 screws securing the lens to base and install jumper on pins 1 2 as shown in Figure 3 Series Star Burst Indicator 19 mm NPT not supplied DC hot or Black AC hot DC common or White AC common hot to activate the Star Burst flicker flash or 65 fpm flash nuts supplied 1 Conduit Mounting 3 4 Shown CT 203 699 3000 FAX 203 699 3365 CUST SERV 203 699 3078 TECH SERV 3100392 ISSUE 1 2002 avoid risk of injury install lens before energizing unit avoid the risk of injury do not start any when unit is energized module lens exterior surfaces should be periodically cleaned a soft clean cloth using water and a mild detergent to main optimum light visibility Disconnect power before cleaning 2 Source Replacement Conduit Mounted Modules Disconnect wiring and if unscrew base from conduit Figure 1 Mounted Modules Disconnect wiring and remove nut securing the base to the panel Figure 2 Remove 4 screws securing the lens to the base from bottom base Figure 4 and remove lens Unplug LED light source and plug in new light source the color of the LEDs is changed the lens color also be changed to match Replace lens on base and secure with 4 screws removed in Nut OD panel hot to activate the Star Burst flicker flash or 65 fpm flash nuts supplied Series Star Burst Indicator DC hot or Black AC hot DC common or White AC common 2 Panel Mounting on pins 1 and 2 standard flash 3 Installing the Jumper View of inside bottom of unit 3100392 ISSUE 1 Series Light PLED Base securing to base LED color R red A amber B blue green or W white 4 Replacing the Light Source 1 Replacement Parts Source 3100392 ISSUE 1