Edwards 125 Class Halogen Instructions

Installation Instructions for 125 Class Beacons 125 Class halogen beacons are UL and cUL listed appliances rated for NEMA 4X applications Two of 125 Class Halogen Beacons are available Flash 125HALF and Steady On 125HALS Both versions be either surface or conduit mounted protective wire guard Cat No 125GRD is available Specifications BASE Number BASE Number Halogen Halogen in this position indicates lens color Amber B Blue C Clear G Green R Red DC AC 50 60 Hz AC 50 60 Hz DC AC 50 60 Hz AC 50 60 Hz Specifications Locations Ratings 31F to 150F 35C to 66C prevent electrical shock ensure that is turned off before installing the Mounting Figure 1 Thread the 18 45.7 cm signal wire leads through either or 3 4 conduit into an approved conduit outlet box is supplied with a double threaded 1 2 internal 3 4 external conduit hub Models Wire the beacon as follows For AC models use wire nuts not supplied and the signal black and white wire leads to the source wires as shown in Figure 1 Polarity not relevant For DC models connect the signal red wire to the power source wire and connect the signal wire to the negative power source wire using nuts not supplied Polarity must be observed to Figure 1 Thread the conduit onto the base of the signal avoid risk of injury install lens before the unit avoid the risk of injury do not remove or lamp when unit is energized Turn on power and verify that the signal operates Mounting Figure 2 When panel mounting the beacon the surface and details of the panel must be taken into in order to ensure that the integrity the outdoor NEMA 4X rating is fully maintained should evaluate Place the mounting gasket supplied over the hole in panel and route the signal wires through the gasket the hole in the panel the base through the hole in the panel and screw locking nut supplied with the raised locking edge the mounting surface onto the base to secure the Wire the beacon as follows For AC models use wire nuts not supplied and the signal black and white wire leads to the source wires as shown in Figure 2 Polarity not relevant For DC models connect the signal red wire to the power source wire and connect the signal wire to the negative power source wire using nuts not supplied Polarity must be observed to Figure 2 Turn on power and verify that the signal operates 3101650 ISSUE 3 2010 Phone 800 336 4206 Fax 800 454 2363 avoid risk of injury install lens before the unit avoid the risk of injury do not start any when unit is energized prevent electrical shock disconnect all and wait five 5 minutes for stored in strobe modules to dissipate starting work on unit power before cleaning The module lens exterior should be periodically cleaned with a soft clean using water and a mild detergent to maintain optimum visibility Replacement Conduit Mounted Modules Disconnect wiring and if unscrew base from conduit Figure 1 Mounted Modules Disconnect wiring and locking nut that secures the base to the panel 2 Remove 4 screws that secure the lens to the base from of base Figure 3 and remove lens Replace halogen lamp as follows Figure 3 Grasp the metal base of the halogen lamp and push lamp down while turning counterclockwise Then the lamp directly upward to remove from the Grasp the new halogen lamp by its base and insert the socket Push down and rotate clockwise to in place Do not touch glass surface of lamp at Reattach lens to base and fasten with screws removed time step 2 1 Conduit Mounting 3 4 Shown 2 Panel Mounting Nut OD panel Class Indicator NPT external shown NPT internal not supplied Wire Leads units Red positive units Black Hot units Black negative units White neutral nuts supplied Source Class Indicator Wire Leads Nuts Supplied Source 3101650 ISSUE 3 3 Lamp Replacement Lamp Shown Socket in groove Screws securiing to base 1 Replacement Parts Number base Lamp Number base Halogen Halogen or industry trade 1692 incandescent or industry trade 15T7DC incandescent or industry trade 1692 incandescent or industry trade 15T7DC incandescent in this position indicates lens color Amber B Blue C Clear G Green R Red listed non halogen lamp may be used in place of the halogen lamp 3101650 ISSUE 3 800 336 4206 800 454 2363 519 376 2430 519 376 7258 852 2907 8108 852 2142 5063 61 3 9239 1200 61 3 9239 1299 32 2 725 11 20 32 2 721 86 13 America 305 593 4301 305 593 4300