Edwards 5510M Installation Instructions

Installation Instructions for Adaptatone Millennium Audio Signal Converter Series 5510M and Operation and Operation and Operation and Operation and Operation Remote Audio Signal Converter is intended for applications where high audible output and reliability are required Series 5510M are UL and cUL Listed as Audible Appliances for use in the following hazardous I Div 2 Groups A B C D II Div 2 Groups F G III Div 1 and 2 135C 100C Audio Signal Converter operates from local power 5510M 25Y6 converts 25V RMS audio signal to 10V for use with the 5532M Adaptatone Speaker Ampli The 5510M 70Y6 converts a 70V RMS audio signal 10V RMS for use with the Edwards 5532M Adaptatone or other 10V RMS applications 6 Pounds 2.7 kg Locations UL Standard UL1604 Temp 41F to 104F 5C to 40C Locations Ambient Temp 40F to 151F 40C to 66C Specifications Specifications Specifications Specifications Specifications On A Audio Signal Converter DC DC AC 50 60 Hz AC 50 60 Hz Adaptatone may be mounted to any flat surface or be used as a freestanding unit mounted to a rigid The Adaptatone must be installed in accordance the latest edition of the National Electrical Code or regulations applicable to the country and locality installation and by a trained and qualified electrician The increased resistance due to long wire runs to be accounted for in sizing wire Applications Engineering for details A U T I O N A U T I O N A U T I O N A U T I O N A U T I O N installation care must be taken so that components the printed circuit board are not damaged Mount Adaptatone as shown in Figure 1 Flat Surface Mounting Secure unit to surface using the 4 mounting holes in mounting plate on the rear of the box Use 10 x 3 76 mm wood screws furnished loose other hardware not supplied suitable for the surface Rigid Pipe Mounting Loosen the 4 cover screws the signal box and lift off signal box cover Cover screws are captive Do not remove from the center knockout in lower wall of box mount box to a 1 2 12.7 mm conduit pipe suitable connector wires through a knockout hole in the bottom the box from a raceway that is with its connections the 1 2 12.7 mm conduit knockout hole approved the same degree of protection and enclosure type by the application Use the provided plastic on the barrier to the electronics to separate power leads from signal and tone initiating per NEC Figures 4 5 and 6 Box Cover Collar and connections supplied the 1 2 12.7 mm hole 10 x 3 76 mm or other hardware for the mounting surface 1 Adaptatone Mounting CT 203 699 3300 FAX 203 699 3365 CUST SERV 203 699 3078 TECH SERV 3100359 ISSUE 2 2002 A R N I N G A R N I N G A R N I N G A R N I N G A R N I N G prevent fire and shock wire the Adaptatone only as in this installation instruction Wire as follows referring to Figures 2 through 5 Connect green and yellow striped earth ground to earth ground See Figure 4 For 5510M 25Y6 connect 25V RMS input to the AUD terminal on the Coupler Board Connect 25V RMS audio to the AUD terminal on the Audio Board Figure 4 For 5510M 70Y6 connect 70V RMS input to the AUD terminal on the Coupler Board Connect 70V RMS audio to the AUD terminal on the Audio Board Figure 4 Connect 10V RMS audio output terminal A on the Audio Coupler Board 10V RMS audio output to terminal B the Audio Coupler Board Connect incoming power to wire leads using a splice or other method listed certified or approved by local authorities Leads black for line and white for neutral See Figure Optional Connect external 24V DC battery not in series with separate diode assembly 2600010 supplied to TB1 terminals 3 and 4 the main board as shown in Figure 7 and on the diode assembly Terminal Block TB1 can be unplugged from the board to complete wiring as shown in 2 A R N I N G A R N I N G A R N I N G A R N I N G A R N I N G ensure integrity of the enclosure Ensure the cover part number P 007549 0069 is adhered into at cover perimeter before replacing the signal box that the 4 collar gaskets part number P 041930 are in place on each cover screw before securing the box cover securing cover start screws by hand making sure are threaded into tapped holes in housing bosses securing with a screwdriver Torque signal box cover to a minimum of 20 in lbs This ensures the tight fit Tightly secure the signal box cover using 4 retained Torque signal box cover screws to a minimum of 20 screws Verify operability and and and TTTTTestestestestest and and A R N I N G A R N I N G A R N I N G A R N I N G A R N I N G that power is disconnected before cleaning inside of the unit semi annually for accumulation of dirt if necessary Adaptatone should be tested annually or as required the authority having jurisdiction to ensure continuous Block is factory to internal supply optional 24V DC Backup 2 Wiring to Terminal Block TB 1 Assembly 3100359 ISSUE 2 2 and and or black for yellow green for tie wrap provided to separate power leads signal and tone initiating leads signal leads from 25V RMS 5510M 25Y6 70V RMS 5510M 70Y6 audio source and 10V RMS audio signal leads to Audio Coupler Board as 3 Wiring the 5510M Series Remote Signal RMS OUT COUPLER BOARD IN IN audio in is 25V RMS for 5510M 25Y6 and 70V RMS for 5510M 70Y6 4 Wiring Audio Signal Leads to 5510M BOARD OF FOR ADJUSTMENT 5 5510M Series PC Board Locations 3 3100359 ISSUE 2