Edwards 5536M Series Installation Instructions

Installation Instructions for Catalog Series 5536M 24 and Adaptatone Millennium Local System Signal 7 8 mm 1 4 mm mm 1 2 mm 3 4 mm 1 2 mm 1 Dimensions and Operation and Operation and Operation and Operation and Operation Adaptatone is a heavy duty tone selectable stand indoor outdoor audible signaling device intended industrial applications where high audible output and reliability are required Catalog Numbers with suffixes 24AQ or 24Y6 are CE Marked and Certified for compliance to the European Electromagnetic Compatibility Industrial and Low Safety Directives see Declaration of Conformtiy upon request Additionally the Adaptatone series are UL and cUL Listed as Audible Signal for use in the following hazardous locations I Div 2 Groups A B C D II Div 2 Groups F G III Div 1 and 2 135C 100C Adaptatone operates from local power and sounds a decibel signal determined by the setting of minia programming switches inside the unit The may be programmed for any of the 27 tones in Figure 11 tones may be programmed into the unit at any time tones operate on a pyramid type priority system tone programmed on SW2 overrides the tones pro on SW3 and SW4 The tone on SW3 overrides tone programmed on SW4 An external audio signal to 12V RMS can be connected to take priority over all generated tone signals decibel output level and speaker lateral position are easily adjustable Specifications Specifications Specifications Specifications Specifications 9 Pounds 4.1 kg Locations UL Standard UL1604 Temp 41F to 104F 5C to 40C Locations Ambient Temp 40F to 151F 40C to 66C Locations and Variable Ambient Conditions apply only UL listings are accepted and do not apply to CE conformity or Certification Specifications Specifications Specifications Specifications Specifications Board Power A Current Tone On Volume DC mA DC DC DC mA mA AC 50 60 Hz AC 50 60 Hz DC DC AC 50 60 Hz AC 50 60 Hz Volume mA mA DC DC AC 50 60 Hz 24V DC mark and T Certifications do not apply to 125V DC or 250V DC AC 50 60 Hz AC 50 60 Hz DC DC Adaptatone may be mounted to any flat surface or be used as a freestanding unit mounted to a rigid The Adaptatone must be installed in accordance the latest edition of the National Electrical Code or regulations applicable to the country and locality installation and by a trained and qualified electrician The increased resistance due to long wire runs to be accounted for in sizing wire Applications Engineering for details catalog numbers ending in AQ 24V AC power must transformer isolated from mains or line power A R N I N G A R N I N G A R N I N G A R N I N G A R N I N G prevent fire shock and component damage NO work circuit board removal should be performed while circuit is energized Any kind of service or maintenance performed unit is energized will void the warranty Mount Adaptatone as shown in Figure 2 Flat Surface Mounting Secure unit to surface using the 4 mounting holes in mounting plate on the rear of the box Use 10 x 3 76 mm wood screws furnished loose other hardware not supplied suitable for the surface Rigid Pipe Mounting Loosen the 4 cover screws the signal box and lift off signal box cover Cover screws are captive Do not remove from the center knockout in lower wall of box mount box to a 1 2 12.7 mm conduit pipe suitable connector CT 203 699 3300 FAX 203 699 3365 CUST SERV 203 699 3078 TECH SERV 3100009 ISSUE 2 2003 1 Programming Logic Controller PLC Compatibility PLC output to meet following product input See Figure 10 voltage off state current mA on current inrush duration A R N I N G A R N I N G A R N I N G A R N I N G A R N I N G No Board Circuit DC only 60 Hz DC only DC wires through a knockout hole in the bottom the box from a raceway that is with its connections the 1 2 12.7 mm conduit knockout hole approved the same degree of protection and enclosure type by the application Use the provided plastic on the barrier to the electronics to separate power leads from signal and tone initiating per NEC Figure 3 star nut to speaker Box Cover Collar and connections supplied to 12.7 mm knockout 10 x 3 76 mm or other hardware for the mounting surface 2 Adaptatone Mounting prevent fire and shock wire the Adaptatone only as in this installation instruction Wire as follows Connect green and yellow striped earth ground to earth ground Select the appropriate method for wiring to the board Figure 9 from Figures 5 10 Connect Adaptatone as shown Connect incoming power to wire leads using a splice or other method listed certified or approved by local authorities Leads both black for AQ and N5 models and are for line and white for neutral for Y6 models Optional Connect external 24V DC battery not in series with separate diode assembly 2600010 supplied to TB1 terminals 3 and 4 the main board as shown in Figure 4 and on the diode assembly Terminal Block TB1 can be unplugged from the board to complete wiring as shown in 4 Refer to Figures 9 and 11 and select desired tones Set miniature programming switches on the input input connected to IN2 set on SW2 IN3 set on IN4 set on SW4 in order of priority desired Connection to IN1 is factory wired from Audio Board for the external audio signal and priority over other signals when activated by 24V DC priority signal Figures 7 and 8 VOLTAGE is present when product is energized High may cause harm to personnel in close proximity Adjust volume level if desired by turning located on the main board Figure 9 ensure integrity of the Adaptatone assembly when the speaker direction make sure threads in the remain fully engaged and do not turn speaker than 360 degrees from the original factory installed To adjust speaker direction loosen large star nut 2 and turn speaker to the approximate desired Retighten nut and turn speaker slightly until locked into place ensure integrity of the enclosure Ensure the cover part number P 007549 0069 is adhered into at cover perimeter before replacing the signal box that the 4 collar gaskets part number P 041930 are in place on each cover screw before securing the box cover securing cover start screws by hand making sure are threaded into tapped holes in housing bosses securing with a screwdriver Torque signal box cover to a minimum of 20 in lbs This ensures the tight fit Tightly secure the signal box cover using 4 retained Torque signal box cover screws to a minimum of 20 screws Verify operability 3100009 ISSUE 2 2 Adaptatone should be tested annually or as required the authority having jurisdiction to ensure continuous and TTTTTestestestestest and and and and A R N I N G A R N I N G A R N I N G A R N I N G A R N I N G prevent fire shock and component damage NO work circuit board removal should be performed while