Edwards CBR & WBR Installation Instructions

Installation Instructions for AdaptaBeacon Catalog No WBR Wall Bracket and Catalog No CBR Corner Mount Bracket Corner Connections Base of Detail A Conduit and by others Box by others required Screw Conduit A Indoor Mounting Only 1 Corner Mount Bracket Surface Wiring Edwards Wall Bracket and Corner Bracket are designed for with Edwards AdaptaBeacon visual signals having a base suit for 1 2 13 mm or 3 4 19 mm conduit mounting CBR Corner Mount Bracket may be used only with surface conduit wiring see Figure 1 The WBR Wall Mount may be used with surface installed conduit wiring see 2 or with concealed conduit wiring see Figure 3 brackets must be installed in acordance with the National Code NEC Canadian Electrical Code CEC local and the local authority having jurisdiction and using ap connection means Mount Figure 1 Use the corner section of the bracket as a template to mark the of the four mounting screws on the mounting surface Drill the four mounting holes at the positions described in 1 Drill size should be determined by the size of the anchors and mounting screws not supplied Remove the 1 2 13 mm knockout from the bottom of the For indoor applications install a 1 2 13 mm set connector and locknut as shown in Detail A For outdoor use appropriate conduit hardware A pull box be used to simplify installation Referring to instructions supplied with the AdaptaBeacon bracket and secure AdaptaBeacon routing field and power wiring and making ground and power connections appropriately external threaded nipple protruding from the bracket arm for securing the AdaptaBeacon A ground terminal is for securing ground to the bracket in back of the arm Two 1 4 20 x 1 1 4 32 mm screws are provided mount bracket arm to the corner section the Edwards AdaptaBeacon includes a 3 4 19 mm conduit entrance assemble the 3 4 1 2 19 13 reducing bushing to the external threaded nipple from the bracket not make power connections within the bracket Turn on the power to verify that the signal operates properly CT 203 699 3300 FAX 203 699 3365 CUST SERV 203 699 3078 TECH SERV SOUND CANADA 519 376 2430 FAX 519 376 7258 ISSUE 3 2001 not make power connections within the bracket Mount Surface Conduit Wiring Figure 2 Use the backplate as a template to mark the positions of the mounting screws on the mounting surface Drill the four mounting holes at the positions described in 1 Drill size should be determined by the size of the anchors and mounting screws not supplied Use oval head screws for mounting Remove the 1 2 13 mm knockout in the bottom of the For indoor applications install a 1 2 13 mm set connector and locknut as shown in Detail A of Figure 1 outdoor applications use appropriate conduit hardware pull box may be used to simplify installation Referring to instructions supplied with the AdaptaBeacon bracket and secure AdaptaBeacon routing field and power wiring and making ground and power connections appropriately external nipple protruding from the bracket arm is for the AdaptaBeacon A ground terminal is provided securing ground to the bracket in back of the bracket arm 1 4 20 x 1 1 4 32 mm screws are provided to mount arm to the backplate the Edwards AdaptaBeacon includes a 3 4 19mm conduit entrance assemble the 3 4 1 2 19 13 reducing bushing to the external threaded nipple from the bracket arm Turn on the power to verify that the signal operates properly Mount the backplate to the installed standard 4 102 mm or 4 102 mm octagonal electrical outlet box with head screws Mount the bracket to the backplate with the two 1 4 20 x 1 1 32 mm screws provided Referring to instructions supplied with the AdaptaBeacon bracket and secure AdaptaBeacon routing field and power wiring and making ground and power connections appropriately external threaded nipple protruding from the bracket arm for securing the AdaptaBeacon A ground terminal is for securing ground to the bracket in back of the arm Two 1 4 20 x 1 1 4 32 mm screws are provided mount bracket arm to the backplate the Edwards AdaptaBeacon includes a 3 4 19 mm conduit entrance assemble the 3 4 1 2 19 mm 13 mm reducing bushing to the external threaded protruding from the bracket arm not make power connections within the bracket Turn on the power to verify that the signal operates properly Connections Base of Detail A Conduit and by others Box by others required 2 Wall Mount Bracket Surface Wiring Connections Base of Bracket 3 Wall Mount Bracket Concealed Wiring Mount Concealed Conduit Wiring Figure 3 and Screws others ISSUE 3