Edwards Data Sheet Remote Booster Power Supplies

Edwards Signaling Catalog u Power Supplies and Accessories Features Allows for reliable filtered and regulated power to be installed needed Cost effective system expansion Provides for Genesis and Enhanced Integrity notification ap synchronization Supports coded output operation Self restoring overcurrent protection Multiple signal rates Can be cascaded or controlled independently On board diagnostic LEDs identify wiring or internal faults Standard Edwards keyed lockable steel cabinet with remov field configuration door and 230 Vac models available Accommodates 18 to 12 AWG wire sizes Optional tamper switch Dual battery charging rates Booster Supplies EBPS10A Booster Power Supply EBPS is a UL 864 9th Edition listed supply It is a 24 Vdc filtered regulated and supervised that can easily be configured to provide additional notification circuits NACs or auxiliary power for Mass Notification Communication MNEC as well as life safety security access control applications EBPS contains the circuitry to monitor and charge internal external batteries Its steel enclosure has room for up to two ampere hour batteries For access control only applications EBPS can support batteries totaling up to 65 ampere hours in external enclosure The EBPS has four Class B convertible to Class A NACs These can be activated in one or two groups the EBPS unique dual input circuits EBPS is available in 6.5 or 10 ampere models Each output has a capacity of three amperes total current draw cannot the unit rating EBPS meets current UL requirements and is listed under the standards CCN 9th ed ition UOXX Fire Alarm Systems ANET UEHX7 AOTX AOTX7 ALVY UEHX7 APAW APAW7 Police Station Connected Burglar Alarm Units and Systems APOU APOU7 Proprietary Burglar Alarm System Units AMCX UOXXC AOTX7 No 205 Station Alarm Unit Units Fire Alarm Canada Burglar Alarm Units and Systems Canada Equipment Canada Alarm Units and Systems Burglar Alarm Units and Systems Control Systems 1 of 4 D A T A S H E E T S85005 0125 to be used for installation purposes Issue 5 View View knockouts 3 4 in conduit cm in cm in cm in cm in cm in cm in cm routing EBPS provides additional power and circuits for notification and other 24 Vdc loads It is listed for indoor dry loca and can easily be installed where needed conditions are indicated on the on board diagnostic LEDs the EBPS input sense circuit and the trouble relay if While this provides indication to the host system EBPS can still be activated upon command A separate AC contact is available on the EBPS circuit board which can be for trouble or AC Fail There are seven on board LEDs one for each NAC fault one for battery fault one ground fault and one for AC power unique dual input activation circuits of the EBPS can be by any voltage from 6 to 45 VDC filtered regulated or to 33 Vdc full wave rectified unfiltered The first input circuit be configured to activate 1 4 of the four possible outputs The input circuit can be configured to control circuits 3 and 4 outputs are configured for auxiliary operation these circuits be configured to stay on or automatically deactivate 30 sec after AC power is lost This feature makes these circuits ideal door holder applications The EBPS also has a separate 200 24 Vdc output that can be used to power internal activation NACs can be configured for a 3 3 3 temporal or continuous California temporal rate outputs are also available on cer models This makes the EBPS ideal for applications requiring rates that are not available from the main system addition to the internally generated signal rates the EBPS can be configured to follow the coded signal rate of the main NACs This allows for the seamless expansion of existing EBPS enclosure has mounting brackets for up to three Signa modules to the right of the circuit board Specification where needed Edwards EBPS Series Booster Power EBPS that are interconnected to and supervised by the system The EBPS shall function as a stand alone auxiliary supply with its own fully supervised battery compliment EBPS battery compliment shall be sized to match the require of the main system The EBPS shall be capable of supervis and charging batteries having the capacity of 24 ampere hours Mass Notification Emergency Communication MNEC life and security applications and the capacity of 65 ampere for access control applications EBPS shall provide a minimum of four independent fully su Class B circuits that can be field configurable for notifica appliance circuits or auxiliary 24 Vdc power circuits EBPS shall be convertible to a minimum of two Class A NACs EBPS output circuit shall be rated at 3 amperes at 24 Vdc output circuit shall be provided with automatically restoring protection The EBPS shall be operable from the main NAC and or Edwards Signature Series control modules NACs shall be configurable for continuous 3 3 3 temporal optionally California rate Fault conditions on the EBPS shall impede operation of main system NAC The EBPS shall be with ground fault detection circuitry and a separate AC relay Maintain 1 4 inch 6 mm spacing between power limited and nonpower limited or use type FPL FPLR or FPLP cable per NEC Power limited and supervised when not configured as auxiliary power Non when configured as auxiliary power Source must be power limited Source determines supervision When using larger batteries make sure to position the battery terminals towards door 2 of 4 D A T A S H E E T S85005 0125 to be used for installation purposes Issue 5 Wiring or cascaded booster on a notification appliance circuit Circuit Circuit NAC end of line resistors are not required to be at the booster terminals This allows multiple to be driven from a single NAC circuit without the for special configurations Alarm Panel next signaling booster or resistor output 1 output 2 output 3 output 4 Power listed 15 KOhm listed 15 KOhm the Booster for Power Fail delay operation E NAC modules using the sense inputs appliance circuit NAC appliance circuit NAC appliance circuit NAC appliance circuit NAC mA AUX 1 2 47 k listed 15 k Ohm listed 15 k Ohm Module mA AUX 1 2 47 K 47 K in from device loop controller out to device in from previous or Signature out to device Booster supports AC Power fail delay three hours via its trouble contact when switch SW2 6 is on All other troubles reported to supervising module or panel delay via Sense inputs Module Module 3 of 4 D A T A S H E E T S85005 0125 to be used for installation purposes Issue 5 us 1 800 336 4206 www edwardssignaling com Signaling is EDWARDS brand Farm Glen Boulevard CT 06032 Canada contact Chubb Edwards Email inquiries chubbedwards com Web www chubbedwards com 2013 UTC Fire Security Americas Inc All rights reserved subject to change notice Edwards is part of UTC Controls Security a unit of Technologies Corporation Line Voltage Appliance Ratings Relay