Edwards F-DACT(F) Digital Alarm Communicator Transmitter Installation Sheet

Digital Alarm Communicator Installation Sheet F DACT F is a digital alarm communicator transmitter for fire alarm control panels The F DACT F also called dialer transmits system status changes events to a digital alarm communicator receiver over the public telephone network The dialer is capable of split to two different account and telephone numbers addition to dialer functions the F DACT F provides LCD to display event messages and programming event history log of panel and DACT events modem for uploading and downloading panel history and current status to a PC running software The F DACT F modem is only rated for 2400 baud Some PC modems may not be compatible this baud rate F DACT F can be programmed to operate as a single or line DACT Modem LCD display a Modem LCD display or LCD display only For the F DACT F to be NFPA 72 CS the following are required factory installed warning label must be removed from F DACT F line two phone jack second phone line independent of that used for line one be connected to phone jack two F DACT F must be programmed for dual line F DACT F must be programmed to transmit a test at least once every 24 hours the JP1 wire loop intact configures the F DACT F for downloading The panel will not allow changes to the or dialer configuration unless the program jumper is It will allow changes to receiver information account telephone numbers etc UL requires the red wire loop be intact for all remote station systems additional download security the F DACT F can be to perform a callback function to prevent access to the panel programming F DACT F is listed for use with the digital alarm receivers listed below CAN ULC S559 compliant configurations for fire signal centre and proprietary fire signal receiving centre refer to CAN ULC S559 Supplement Manual 3101563 Knight 4 2 Contact ID 4 2 Contact ID 4 2 Contact ID 4 2 4 2 Contact ID 4 2 4 2 Contact ID 2000 MLR2 TLR EST 4 2 is SIA DCS 02 P3 with the ability to transmit event codes Information The dialer complies with Part 68 of the FCC rules The FCC certification number and Ringer Equivalence REN are displayed on the panel programming and in this manual This information must be to the telephone company if requested Two FCC compliant telephone cords with 8 pin modular at both ends are supplied with the FSDACT The is designed to be connected to the telephone using the supplied cord and an RJ 31X or RJ 38X which must also comply with FCC Part 68 rules The REN is used to determine the maximum number of that may be connected to a single telephone All telephone devices are assigned a REN The of the RENs for all connected devices may not five The maximum REN may vary in some areas the local telephone provider for more information the dialer causes harm to the telephone network the company will notify you an advance that discontinuance of service may be required If notice is not practical the telephone company notify you as soon as possible You will also be of your right to file a complaint with the FCC if believe it is necessary The telephone company may make changes in its equipment operations or procedures that could the operation of the dialer If this happens the company will provide advance notice in order 2013 UTC Fire Security All rights reserved 4 3101038 REV 03 REB 25JAN13 instructions the F DACT F according to the instructions provided High voltages capable of causing personal injury death may be present Disconnect all sources of then wait at least 30 seconds for capacitors to discharge a safe energy level before proceeding Failure to disconnect power will damage the panel the F DACT F Observe static sensitive handling It is not necessary to remove the main panel board from cabinet to install the the F DACT F install the F DACT F Remove the clear plastic film protecting the LCD on the Mount the F DACT F to the back of the circuit board See 1 this is a new installation remove the insert from the LCD on the control panel Connect the power cable to J2 on the control panel Connect the supplied modular phone cables to the jacks See Figure 2 Energize the control panel programming instructions refer to the technical manual under Protected Premises Control on the label attached to the inside of the cabinet door addition if you are installing the F DACT F in a FireShield panel see for FireShield control panels in this document you to make necessary modifications to maintain service trouble is experienced with the dialer for repair or information contact Fire Security Town Center Parkway FL 34202 800 655 4497 the dialer is causing harm to the telephone network the company may request you disconnect the dialer the problem is resolved No repairs may be performed on the dialer by the user The dialer can not be used on public coin phones or party service provided by the telephone company Canada Information This equipment meets the applicable Industry Terminal Equipment Technical Specifications This is by the registration number The abbreviation IC the registration number signifies that registration was based on a Declaration of Conformity indicating that Canada technical specifications were met It does not that Industry Canada approved the equipment installing this equipment users should ensure that it is to be connected to the facilities of the local company The equipment must also be using an acceptable method of connection The should be aware that compliance with the above may not prevent degradation of service in some to certified equipment should be coordinated by a designated by the supplier Any repairs or made by the user to this equipment or equipment may give the telecommunications company to request the user to disconnect the equipment should ensure for their own protection that the electrical connections of the power utility telephone lines and metallic water pipe system if present are connected This precaution may be particularly important in rural Users should not attempt to make connections but should contact the appropriate electric authority or electrician as appropriate The Ringer Equivalence Number REN for this equipment is 0.1 The REN assigned to each terminal provides an indication of the maximum number of allowed to be connected to a telephone interface termination on an interface may consist of any of devices subject only to the requirement that the of the Ringer Equivalence Numbers of all the devices not exceed five 4 3101038 REV 03 REB 25JAN13 1 F DACT F installation 2 Typical RJ 31X connection premises down block 1 Line 2 1 jack LINE 2 jack block by installer 4 conductor cord for FireShield control panels you are installing the F DACT F into a FireShield control you will see these new programming options Daylight saving time instructions for these new options are provided 1 and Line 2 supervision duration call dialing ground fault check saving time daylight saving time DST option determines when and much the system clock is adjusted for daylight saving default DST settings adjust the system clock forward one on the second Sunday in March at 2 00 a m and back hour on the first Sunday in November at 2 00 a m change daylight saving time settings Select the Daylight Saving option Enter Set For DST Adjustment enter how m