Edwards Genesis Low Frequency (520 Hz) Horn Installation Sheet

Genesis Low Frequency 520 Hz Horn Sheet and wire this device in accordance with applicable and local codes ordinances and regulations Electrical supervision requires that you break the wire at each terminal Do not loop wires around the terminals install the horn Remove the cover by using a screwdriver to depress and twist both tabs on top of the unit Set the horn signal and sound output level to desired See Figure 1 change the horn output level from high dB to low dB jumper JP3 change the horn signal from temporal to steady cut JP2 Mount the horn as follows Route the signal circuit field wiring through the in the center of the horn mount Mount the horn and flush mount spacer a compatible electrical box Figure 2 making sure to overtighten the mounting screws See for compatible electrical boxes mount Mount the G4B or G4RB surface mount on the wall or ceiling Figure 3 and then secure the to the box using the screws provided with the Connect the signal circuit field wiring to the horn terminals 4 Observe polarity for the unit to function Replace the cover by aligning it at the bottom and then it in at the top Figure 2 and Figure 3 Test the unit for proper operation Genesis Low Frequency 520 Hz horn can be used for where a low frequency alarm notification appliance required The device is designed for indoor use only and can mounted on the wall or ceiling See Table 1 for a list of numbers horn includes field configurable jumper options for High dB or low dB output or steady horn output 1 Models frequency 520 Hz horn white housing FIRE marking frequency 520 Hz horn white housing FIRE marking frequency 520 Hz horn red housing no marking frequency 520 Hz horn red housing FIRE marking mount box white housing mount box red housing 2014 UTC Fire Security Americas Corporation Inc 4 3102148 EN REV 02 ISS 25MAR14 1 Horn settings 3 Surface mount Jumper JP3 Jumper JP2 Surface mount box G4B or Screw 4X provided with Horn or G4RB box Cover 2 Flush mount 4 Wiring diagram Compatible electrical box Flush mount spacer Horn 8 32 x 1 in screw 2X Cover From NAC output To next device or EOL Polarity is shown in the active condition 4 3102148 EN REV 02 ISS 25MAR14 To maintain the required agency listings do not factory applied finishes unit is not serviceable or repairable Should the unit fail to contact the supplier for a replacement a visual inspection and an operational test twice a or as directed by the local authority having jurisdiction voltage level output directional size electrical environment humidity VDC or 24 VFWR 1 mA at 16 VDC 215 mA at 16 VFWR Table 4 Table 2 and Table 3 Table 5 and Table 6 to 18 AWG 1.0 to 4.0 mm 4 in square box 1 1 2 in 38 mm in 54 mm deep box or G4B G4RB mount box to 120 0 to 49 to 93 noncondensing This device was tested to the Regulated 24 DC FWR operating limits of 16 V and 33 V Do not apply 80 and 110 of these for system operation 2 UL sound level output dBA 1 and voltage VDC VDC VDC VDC VDC VDC UL 464 Sound level output at 10 ft 3.05 m measured in a room 3 Nominal sound level output dBA temporal tone 1 VDC VDC VDC VFWR VFWR VFWR Measured in an anechoic chamber at 10 ft 3.05 m 4 Nominal operating current in RMS mA and voltage VDC VDC VDC VFWR VFWR VFWR VDC VDC VDC VFWR VFWR VFWR Volts direct current regulated and filtered Volts full wave rectified 5 Audible directional characteristics horizontal pattern 1 dB 2 Angles are measured from a perpendicular axis positive angles to right Peak output at 16 VDC set for steady tone 6 Audible directional characteristics vertical pattern 1 dB 2 Angles are measured from a perpendicular axis positive angles are Peak output at 16 VDC set for steady tone information A Division of UTC Fire Security Corporation Inc Town Center Parkway Bradenton FL USA first two digits of the date code located on product identification label are the year of 24 DC and 24 FWR 464 of American information contact information see www edwardsutcfs com 3102148 EN REV 02 ISS 25MAR14 4 4 3102148 EN REV 02 ISS 25MAR14