Edwards Genesis Temporal Horn-Strobe Installation Sheet

Genesis Temporal Horn Strobe Installation plate plate with FIRE marking are field configurable options for selecting dB output signal or strobe signal output See Figure 1 strobe includes a field configurable switch for selecting the candela output The candela output setting is locked in and remains visible after final installation See Figure 2 strobe features an enhanced synchronization circuit to with the latest requirements of UL 1971 Signaling for the Hearing Impaired and the latest Canadian CAN ULC S526 Synchronized operation requires a installed synchronization control module See 2 for a list of compatible synchronization modules MG1M RM 2 Compatible synchronization module models 1 Signal Master Mount Signal Master Mount Output Module SIGA CC1S SIGA MCC1S Input Signal Module Power Supply Supply Synchronization module requirements are determined by the SIGA MCC2 A this device in accordance with applicable requirements the latest editions of the NFPA codes and standards the Building Code of Canada the Canadian Electrical Part 1 Section 32 and in accordance with the local having jurisdiction Genesis Temporal Horn Strobe is a fire alarm notification designed for indoor walls See Table 1 for a list of numbers 1 Models to 110 multi cd to 110 multi cd with FIRE marking to 110 multi cd to 110 multi cd with FIRE marking plate plate with FIRE marking XLSG1RF HDVM 2010 UTC Fire Security All rights reserved 4 3100560 REV 5.0 ISS 25AUG10 2 Candela switch 3 Wiring diagram From compatible fire alarm control panel To next appliance EOL or return to source Polarity is shown in the alarm condition To maintain the required agency listings do not factory applied finishes unit is not serviceable or repairable Should the unit fail to contact the supplier for replacement a visual inspection and an operational test twice a or as directed by the local authority having jurisdiction Electrocution hazard To avoid personal injury or from electrocution remove all sources of power and stored energy to discharge before installing or removing Electrical supervision requires breaking the wire run each terminal Do not loop the signaling circuit field wires the terminals install the horn strobe Remove the cover by depressing both tabs on the top of unit with a small screwdriver and twisting slightly Set the horn signal sound output level and strobe signal the desired settings See Figure 1 change the strobe to temporal private mode cut circle J1 to the edge of circuit board change the horn signal from temporal to steady from circle J2 to the edge of circuit board change the horn output level from high dB to low cut the J3 trace between the holes Slide the candela switch to the desired candela output by it with the indicator located left of the switch See 2 Connect the strobe terminals to the signal circuit field You must observe polarity for the unit to function See Figure 3 Mount the unit onto a compatible electrical box making not to overtighten the mounting screws Replace the cover by aligning it at the bottom then it in at the top Test the unit for proper operation 1 Horn and strobe settings J3 Strobe signal output Temporal steady horn signal output dB sound output If the strobe is set to temporal private mode this device is no UL 1971 listed and FM Approved but is UL 1638 listed 4 3100560 REV 5.0 ISS 25AUG10 Voltage horn strobe level output directional output settings size electrical environment humidity VDC or 24 VFWR nominal Table 7 Table 3 and Table 4 Table 5 and Table 6 at 15 30 75 and 110 cd allowed resistance between any devices is 20 Refer to specifications the synchronization control module this and the control panel to determine wire resistance flash per second fps to 18 AWG 0.75 to 2.50 mm in 64 mm deep single gang box in square box 1 1 2 in 38 mm 2 gang in octagonal with G1T or G1RT trim to 120 0 to 49 to 93 noncondensing 3 UL Ratings temporal output and voltage 464 Sound level output at 10 ft 3.05 m measured in a room at 16 V 4 Sound level output dBA temporal tone VDC VDC VDC VFWR VFWR VFWR Meets or exceeds 85 dBA in an anechoic chamber at ft 3.05 m 5 Audible directional characteristics horizontal pattern 1 Angles are measured from a perpendicular axis positive angles to right Peak output at 16 VDC set for steady tone dB 2 dB 2 6 Audible directional characteristics vertical pattern 1 Angles are measured from a perpendicular axis positive angles are Peak output at 16 VDC set for steady tone cd 7 Operating horn strobe current in RMS A Volts direct current regulated and filtered Volts full wave rectified currents shown above were measured by UL at 16 VDC and VFWR and high dB setting current 4 UL 1971 minimum light output of rating vs angle 10 15 20 Angle Minimum UL required candela light output of rated candela vertical specification of rated candela horizontal specification 3100560 REV 5.0 ISS 25AUG10 4 5 Typical horizontal light output profile 110 cd setting 350 355 information A Division of UTC Fire Security Corporation Inc Town Center Parkway Bradenton FL USA first two digits of the date code located on product identification label are the year of 24 DC and 24 FWR UL requirements for standards UL 464 1638 and UL 1971 see Figure 1 and requirements for standards ULC S525 ULC S526 of rating American information contact information see www utcfireandsecurity com