Edwards Installation sheet, Genesis WG4 series speaker

WG4 Speaker Installation Sheet this device in accordance with the latest edition of NFPA and the local authority having jurisdiction Electrocution hazard To avoid personal injury or from electrocution remove all sources of power and stored energy to discharge before installing or removing Electrical supervision requires the wire run to be at each terminal Do not loop the signaling circuit field around the terminals The Genesis WG4 Speaker may be ceiling mounted or and may be placed in one of four positions See 4 Place the electrical box accordingly Genesis WG4 Speaker is a fire alarm and mass and emergency communication MNEC appliance for indoor or outdoor wet location use on ceilings or See Table 1 for a list of models and Table 2 for a list of 1 Models wall ceiling speaker 25 70 V multi white with ALERT marking wall ceiling speaker 25 70 V multi white wall ceiling speaker 25 70 V multi red wall ceiling speaker 25 70 V multi white with FIRE marking wall ceiling speaker 25 70 V multi red with FIRE marking 2 Accessories 1 Outdoor rated surface skirt white for Genesis WG4 1 or speaker strobe surface skirt red for Genesis WG4 or speaker strobe replacement gasket The trim skirt is outdoor rated when used with the 449 weatherproof install the speaker Remove the cover from the speaker by first removing the cover screws See Figure 1 desired place the optional trim skirt over the electrical See for a list of compatible boxes Remove the gasket that comes with the 449 weatherproof and replace it with the gasket that comes with the speaker Place the gasket over the backplate and then feed the wiring through the wire slots on the gasket and the See Figure 2 item 2 Secure the backplate to the electrical box with four Connect the wiring to the terminal strip Connect the speaker to the audio NAC Observe polarity Figure 2 Set the speaker voltage default speaker voltage is 70 V For 25 V reposition speaker voltage selection switch S3 See Figure 2 3 Set the wattage wattage default setting is Z corresponding to 1 4 watt select a different wattage align the S1 indicator to the wattage setting See Table 3 and Figure 2 item 1 Position the cover over the backplate and then secure it the six cover screws Test the unit for proper operation 2011 UTC Fire Security All rights reserved 4 3101852 REV 2.0 ISS 21MAR11 1 Exploded view of assembly 3 Assembled Optional skirt Backplate Front cover Cover screws 6X Cover screws 6X Front cover Backplate Optional skirt Gasket Electrical box 2 Wiring and switch locations A S1 wattage setting switch see Table 3 Wire slot Polarity shown in alarm condition S3 speaker voltage setting switch UP position is 70 V default position is 25 V 4 3101852 REV 2.0 ISS 21MAR11 4 Mounting positions NOT PAINT 3 Sound level output dBA W W W W V V Decibels A weighted 1480 Sound level output at 10 ft 3.05 m measured in a room using 400 to 4,000 Hz band limited pink noise information of manufacture American compliance NOT PAINT unit is not serviceable or repairable Should the unit fail to contact the supplier for replacement a visual inspection and an operational test twice a or as directed by the local authority having jurisdiction Do not change the factory applied finish Canada A Division of UTC Fire Security Corporation Inc Town Center Parkway Bradenton FL USA first two digits of the DATE MFG located on the product identification are the year of manufacture UL 1480 NFPA 72 device complies with part 15 of the Rules Operation is subject to the two conditions 1 This device may cause harmful interference and 2 this must accept any interference including interference that may undesired operation Class A digital apparatus complies with ICES 003 information contact information see www utcfireandsecurity com voltage voltage level output response size electrical environment humidity VRMS or 70 VRMS switch selectable VRMS V max Table 3 to 4,000 Hz to 18 AWG 0.75 to 2.50 mm 449 in square by 1 1 2 in deep box to 151 to 66 to 95 noncondensing 3101852 REV 2.0 ISS 21MAR11 4 4 3101852 REV 2.0 ISS 21MAR11