Edwards SA-DACT Dialer Installation Sheet

Dialer Installation Sheet FR Installation Sheet SA DACT provides communications between the control and the central station over a telephone line system The transmits system status changes events to a digital alarm communicator receiver over the public telephone network The DACT queues messages and them based on priority alarm supervisory trouble test monitor and system The dialer is capable of dual or split reporting of events to two different account telephone numbers The modem feature of the DACT can be used for uploading and downloading panel history and current status to a PC running the utility The modem feature uses line 1 only The SA DACT is compatible with Contact ID CID only DACT is installed on the plastic assembly and connects to main circuit board via a ribbon cable install the DACT Power down the panel and disconnect the batteries Locate the dialer card slot on the plastic assembly behind main circuit board and connector J8 on the main circuit at the top center of the main board Slide the DACT into the slot on the plastic assembly as in the diagram Attach the DACT to the plastic assembly using two 6 screws as shown in the diagram Connect the ribbon cable P N 7140188 from the DACT to J8 on the main circuit board Connect the phone lines See Power up the panel and connect the batteries 1 Slide the DACT into its slot circuit board assembly card slot on assembly 2 Screw the DACT in place and connect the ribbon cable cable to connector on main circuit top center plastite screws 2013 UTC Fire Security All rights reserved 8 3101099 REV 03 REB 25JAN13 dialer phone lines connect to connectors on the dialer s circuit board Phone line 1 connects to connector J1 and line 2 connects to connector J4 card typically connects to an RJ 31X block using an 4 conductor modular cord Wire the RJ 31X block shown below Install a listed secondary telephone protector between telco network and the SA DACT card The SA DACT card be the next piece of equipment that connects to the company TELCO telephone lines 3 SA DACT wiring premises down block 2 1 protector protector block by installer 4 conductor cords by installer 2 1 dialer test is a test of the telephone line for each dialer When a dialer is tested a normal or abnormal test depending on the state of the system is sent to the account If the dialer is set up for dual line operation test message is sent to both lines regardless of the success the transmission for either account Before conducting a test configure the dialer accounts proper operation conduct a dialer test Press the control panel s Menu button Choose Test Choose Dialer Select the account that you want to test Press Enter The test message is sent to the CMS account that selected For verification of the CMS account the test message you must be in contact with CMS account during the test Nothing is displayed on LCD display Press Cancel to return to the previous menu or the Menu button to exit menu mode line type line connector formats voltage current registration number Canada number equivalence environment or two loop start lines on a public network C31 38X ID SIA DC 05 VDC 41 mA 100 mA to 120 0 to 49 to 93 RH noncondensing at 90 8 3101099 REV 03 REB 25JAN13 dialer is listed for use with the following DACRs ID ID ID and with a line installed 9800 MLR2 MCDI TLR SG SLR ID ID ID Knight information ensure proper operation this dialer must be installed to the enclosed installation instructions To that the dialer is operating properly and can report an alarm it must be tested immediately installation and periodically thereafter according to enclosed test instructions order for the dialer to be able to seize the phone line to an alarm or other event when other customer telephone answering system computer etc connected to the same line is in use the must be connected to a properly installed RJ 31X The RJ 31X jack must be connected in series with ahead of all other equipment attached to the same line Series installation of an RJ 31X jack is in the wiring diagram If you have any questions these instructions you should consult your company or a qualified installer programming emergency numbers or making test calls emergency numbers remain on the line and briefly explain the dispatcher the reason for the call Perform programming testing activities in the off peak hours such as early or late evenings contains among other information a product in the format US AAAEQ TXXXX If requested information must be provided to the telephone plug and jack used to connect the dialer to the wiring and telephone network must comply with applicable FCC Part 68 rules and requirements by ACTA The dialer must be connected to a RJ 31X or RJ 38X jack using a compliant cord a modular telephone cord is supplied with the dialer it is to meet these requirements See installation for details ringer equivalence number REN is used to determine many devices you can connect to a telephone line If total REN value for all devices connected on a line exceeds that allowed by the telephone the devices may not ring on an incoming call In but not all areas the total REN value should not 5.0 To be certain of the total REN value allowed a telephone line contact the local telephone company products approved after July 23 2001 the REN is part the product identifier in the format The digits represent the REN a decimal point Example 03 is an REN of 0.3 For products the REN is listed separately the dialer is harming the telephone network the company will notify you in advance that discontinuance of service may be required If notice isn practical the telephone company will you as soon as possible You will also be advised of right to file a complaint with the FCC if you believe it necessary telephone company may make changes to its equipment operations or procedures that could the operation of the dialer If this happens the company will provide advance notice in order you to make necessary modifications to maintain service you are experiencing problems with the dialer contact Technical Support for repair or warranty information the dialer is harming the telephone network the company may request that you disconnect the until the problem is resolved dialer contains no user serviceable parts In case of return the dialer for repair may not connect the dialer to a public coin phone or a line service provided by the telephone company equipment approved before July 23 2001 This complies with Part 68 of the FCC rules A label to the dialer contains among other information FCC registration number and ringer equivalence REN for this equipment If requested this must be provided to the telephone company equipment approved after July 23 2001 This dialer with Part 68 of the FCC rules and the adopted by the Administrative Council for Attachments ACTA A label attached to the Canada information The Industry Cana