EST 270217 R1[1] 5 FCCA Series Audio Control Panel

270217 14JUL97 Series Audio Control Manual BY NOTICE Systems Technology Parkland Drive FL 34243 739 4300 1997 Edwards Systems Technology Inc manual and the products it describes are copyrighted by Systems Technology Inc EST You may not reproduce transcribe or transmit any part of this manual without written permission from EST manual contains proprietary information intended for distribution authorized persons or companies for the sole purpose of business with Edwards Systems Technology Inc If you any information contained in this manual to unauthorized you have violated all distributor agreements and we may legal action manual was designed and written by the EST Technical Documentation Department Sarasota Audio Control Panel 2 Wiring System Operation System Operation Audio Control Panel 16 Wiring Wiring 25 for Channel Selections 26 Channel System Operation 30 Code Sequence Programming 30 Volt Audio System Tuning Procedure 31 Volt Audio System Tuning Procedure Series Manual information of liability content of this manual is proprietary in nature and is intended for distribution to authorized persons companies distributors others for the sole purpose of conducting business associated Edwards Systems Technology Inc The distribution of contained within this manual to unauthorized persons shall a violation of any distributor agreements and may result in of legal proceedings product has been designed to meet the requirements of NFPA 72 1996 Edition Underwriters Laboratories Inc Standard 7th Edition and Underwriters Laboratories of Canada Inc ULC S527 Installation in accordance with this manual codes and the instructions of the Authority Having is mandatory EST Inc shall not under any circumstances liable for any incidental or consequential damages arising from loss property or other damages or losses owing to the failure of EST Inc beyond the cost of repair or replacement of any defective EST Inc reserves the right to make product improvements change product specifications at any time every precaution has been taken during the preparation of this to ensure the accuracy of its contents EST assumes no for errors or omissions warning equipment can generate and radiate radio frequency energy If this is not installed in accordance with this manual it may cause to radio communications This equipment has been tested found to comply within the limits for Class A computing devices to Subpart B of Part 15 of the FCC Rules These rules are to provide reasonable protection against such interference this equipment is operated in a commercial environment of this equipment is likely to cause interference in which the user at his own expense is required to take whatever measures be required to correct the interference Series Manual history Series Auido Control Panel Installation Manual P N 270217 Status 1995 1997 For Change Release and content revisions Series Manual Series Manual Audio Control Panel FCCA Audio Control Panel is a 19 rack mounted dual channel interface with paging microphone and master fire fighter and associated controls for use in the system command on single and multi line networks A solid state VU meter is for audio level indication Dual telephone risers are provided with a phone busy riser Integral tone generators are provided for and alarm signaling Inputs are provided for use of pre messages and other external input signal sources Front View SYSTEMS TECHNOLOGY MODEL FCCA FCCA is a rack mounted operator interface emergency voice alarm systems which require paging and fire fighter system operation These panels may be located local to or from the main network controller and communicate via RS 485 mA loop or fiber optic links as Class B only The FCCA is suitable use with CM1N w RM option PCPU RMDP 1N two columns of switches on the FCCA front panel are labeled 1 AREA and Channel 2 AREAS The is defined as those locations which receive primary notification a fire alarm is received These are typically located on the fire the floor above and the floor below These locations receive the signal which may be one of 15 tones a pre recorded message a message originating from the FCCA or a page message from a fire fighter telephone and patched through to the 1 audio riser In dual channel operations the FCCA Channel 1 is distributed throughout the building on riser B which is with the traditional cards ZB8 2 ZB8 5 or ZB8 8 With Series Manual Series the area will receive signals present on Channel which may be one of 15 tones a pre recorded message a page originating from the FCCA or a page message originating a fire fighter telephone and patched through to the SIGA 2 audio riser which is associated with the SIGA CC2 module Channel 2 areas are areas of the building defined as all not included in the fire area These locations receive the present on channel 2 which may be one of 15 tones a pre message a page message originating from the FCCA or a message originating from a fire fighter telephone and patched to the FCCA Channel 2 audio riser The FCCA Channel 2 is distributed throughout the building on riser A which is with the traditional cards ZB8 2 ZB8 5 or ZB8 8 With Series the area will receive signals present on SIGA 1 which may be one of 15 tones a pre recorded message a message originating from the FCCA or a page message from a firefighter telephone and patched through to the Channel 1 audio riser This is associated with a SIGA CC2 and TAPE signals may be automatically or manually activated and PHONE PAGE are both manually activated Speaker and fire telephone circuit supervision and selection are performed by control modules RZB12 6 remote zone modules or traditional series zone modules Dual channel switching can only be done an RZB12 6 or a ZB series zone module With Signature Series SIGA CC2 an analog addressable device can be used to connect to two signal risers riser 1 and riser 2 Upon command from the controller the SIGA CC2 can connect the Notification Appliance to either riser 1 or riser 2 Riser 1 and riser 2 inputs may be 24 to operate polarized audible and visual signals or 25V or 70V to audio evacuation circuits FCCA requires a display switch panel models RASP SAN or and or an annunciator operator interface for controlling individual audio and telephone branch circuit status HWD Environment Requirements Format Class B Only Line TB3 4 to TB3 5 x 19 x 5.25 lbs 49o C 32 120o F Non Condensing VDC 280 mA 20 mA Current Loop Fiber Optics w SO 20 or SO FIB JP1 Series Manual Impedance Voltage K EOL Amplifier Load Response Input Voltage Input Voltage Type Amplifiers Channel Max 1 kHz Impedance Outputs Input TB1 10 TB1 11 TB1 TB1 13 Input TB1 20 TB1 21 Outputs TB2 1 TB2 5 Relays TB1 1 TB1 4 TB1 18 Arrangement Ratings Requirements