EST Booster Power Supply Manual

Booster Power Supply BY NOTICE OF LIABILITY WARNING DEVICES Signal Building Systems Corporation Parkland Drive FL 34243 739 4300 1999 General Signal Building Systems Corporation manual and the products it describes are copyrighted by General Signal Systems Corporation You may not reproduce translate transcribe or any part of this manual without express written permission from Signal Building Systems Corporation product has been designed to meet the requirements of NFPA Standard 72 Edition Underwriters Laboratories Inc Standard 864 7th Edition in accordance with this manual applicable codes and the of the Authority Having Jurisdiction is mandatory General Signal Systems Corporation shall not under any circumstances be liable for incidental or consequential damages arising from loss of property or other or losses owing to the failure of General Signal Building Systems products beyond the cost of repair or replacement of any defective General Signal Building Systems Corporation reserves the right to product improvements and change product specifications at any time every precaution has been taken during the preparation of this manual to the accuracy of its contents General Signal Building Systems assumes no responsibility for errors or omissions equipment can generate and radiate radio frequency energy If this is not installed in accordance with this manual it may cause to radio communications This equipment has been tested and to comply within the limits for Class A computing devices pursuant to B of Part 15 of the FCC Rules These rules are designed to provide protection against such interference when this equipment is operated a commercial environment Operation of this equipment is likely to cause in which case the user at his own expense is required to take measures may be required to correct the interference a complete list of compatible devices refer to P N 85000 0285 HISTORY P N 270946 1999 1999 for change release note to AC power wiring diagram and updated 1 covered 1 1 2 indicators 2 the enclosure 3 Signature Series modules 4 DIP switch setting options 5 switch configuration 5 configuration 7 the Booster Power Supply 8 placement 8 power wiring 9 Class B wiring 9 Class A wiring 9 relay wiring 10 wiring 10 11 circuit power applications 11 applications using Signature Series modules 13 calculation worksheet 15 Vdc Notification Appliance Circuit NAC specifications 16 covered number Amp Booster Power Supply Amp Booster Power Supply Amp Booster Power Supply Amp Booster Power Supply Amp Booster Power Supply Amp Booster Power Supply Amp Booster Power Supply Amp Booster Power Supply Amp Booster Power Supply Amp Booster Power Supply Amp Booster Power Supply Amp Booster Power Supply Amp Booster Power Supply Amp Booster Power Supply Amp Booster Power Supply Amp Booster Power Supply Amp Booster Power Supply Amp Booster Power Supply 10 Amp and 6.5 Amp Booster Power Supplies BPS are to extend a fire alarm panel signaling capacity The can be connected to existing Class A or Class B Appliance Circuits NACs or activated via Series modules There are four independent 3.0 Amp circuits supervised in a non alarm condition Booster has a trouble relay that operates on any Booster The Booster contains a battery charger capable of up to two 10 amp hour 12 V batteries to supply a total 24 Vdc Power Supply Manual line voltage amp Booster amp Booster voltage V input current I input output voltage output current size EOL supv current outputs outputs disabled battery Requirements charger current limit environment temperature humidity V 220 240 Vac 50 60 Hz watts V 220 240 Vac 50 60 Hz watts V 45 V DC or 14 V 32 V unfiltered DC mA 24 Vdc 3 mA 12 Vdc mA 45 Vdc V nominal special application output only A max per circuit 10 A 6.5 A total all NACs 12 AWG K amps max 3 amps max circuit programmable replaces NACs programmable after 30 to 10 AH A max to 120O F 0 to 49O C to 93 RH indicators Booster has six LED indicators There are four NAC trouble one battery trouble LED and one ground fault LED Power Supply Manual the enclosure sure to follow all applicable national NFPA 72 and local alarm codes and standards when installing this system the backbox at the required location A dedicated 120 220 240 Vac 50 60 Hz circuit is required for power all conduit and pull all wiring into the backbox before 8.6 cm 8.9 cm 33.02 cm View 33.02 cm 17.78 cm View knockouts 3 4 conduit cm 8.9 cm Power Supply Manual Signature Series modules mount Signature Series modules Remove the black bracket connected to the module Snap the module in one of the three provided brackets in the to the drawing below Power Supply brackets module module BATTER Y 2 3 4 5 6 7 8 9 10 11 12 S2 AUX Power Supply Manual DIP switch setting options switch configuration 12 position DIP switch is used to configure NAC circuit AC power loss auxiliary outputs and Class A or B The following tables show the positions for each switch the DIP switch for the various input output and panel 2 3 4 5 6 7 8 9 101112 AUX S2 RATE 1 input SW1 1 2 S1 SW1 2 Class B all NACs A both NACs and 3 4 NAC1 only Activates NAC 1 2 NAC 1 2 NACs 1 only NACs 1 2 3 only both NACs and 3 4 2 input SW1 3 4 S2 SW1 4 Class B all NACs A both NACs and 3 4 NAC 3 4 NACs 2 3 4 only NACs 3 only NAC4 only No NACs activated NAC 3 4 A or B configuration SW1