EST EST3 v2 0 Signature Series Component Installation Manual

Signature Series Component Manual 270497 06DEC99 BY NOTICE INFORMATION Systems Technology Parkland Drive FL 34243 739 4300 1997 99 Edwards Systems Technology manual and the products it describes are copyrighted by Systems Technology EST You may not reproduce transcribe or transmit any part of this manual without written permission from EST manual contains proprietary information intended for distribution authorized persons or companies for the sole purpose of business with Edwards Systems Technology Inc If you any information contained in this manual to unauthorized you have violated all distributor agreements and we may legal action manual was designed and written by EST Technical Services Department Sarasota last revisions to this manual were made 06DEC99 City Tie Module Fire Alarm Station 2 Stage Fire Alarm Station Double Action Fire Alarm Station Detector Sounder Base Single Input Signal Module Dual Input Signal Module Control Relay Module Control Relay Reversing Module Single Input Module Dual Input Module Detector Guard Surface Adapter for use with the SIGA DG Detector Duct Detector Housing Assembly Duct Mounting Plate Duct Detector Test Station Fixed Temperature Heat Detector Fixed Temperature Rate of Rise Heat Detector Grade 1 Heat Detector Detector Base Detector Base Isolator Module 4D Multisensor Smoke Detector Ionization Smoke Detector Remote LED Alarm Indicator Class A B Input Output Module Transponder Mounting Bracket Single Input Signal Module Dual Input Signal Module Control Relay Dry Module Control Reversing Relay Module Dual Input Module Monitor Module Mounting Plate Mounting Plate Mounting Plate 3D Multisensor Smoke Detector Photoelectric Smoke Detector Detector Base Detector Base Detector Base Detector Base 4 inch Box Trim Skirt Ring Universal Input Output Motherboard Universal Input Output Motherboard Universal Class A B Module Waterflow Tamper Module Breakglass Station Detector Base Series Component Installation Manual Information of liability product has been designed to meet the requirements of NFPA 72 1993 Edition Underwriters Laboratories Inc Standard 7th Edition and Underwriters Laboratories of Canada Inc ULC S527 Installation in accordance with this manual codes and the instructions of the Authority Having is mandatory EST shall not under any circumstances be for any incidental or consequential damages arising from loss of or other damages or losses owing to the failure of EST beyond the cost of repair or replacement of any defective EST reserves the right to make product improvements and product specifications at any time every precaution has been taken during the preparation of this to ensure the accuracy of its contents EST assumes no for errors or omissions warning equipment can generate and radiate radio frequency energy If this is not installed in accordance with this manual it may cause to radio communications This equipment has been tested found to comply within the limits for Class A computing devices to Subpart B of Part 15 of the FCC Rules These rules are to provide reasonable protection against such interference this equipment is operated in a commercial environment of this equipment is likely to cause interference in which the user at his own expense will be required to take whatever may be required to correct the interference Series Component Installation Manual History Series Component Installation Manual P N 270497 Status For Change Release the following installation sheets to the manual CRR MAB MCR MCRR MCC1 MCC2 MCT2 and UIO6 R Remove SIGA RB Sounder Base Series Component Installation Manual Series Component Installation Manual VDC out to next device if required Wiring Box VDC IN OUT VDC IN OUT VDC out to next device if required Wiring Box 200mA into a 14.5 coil loop resistance 25 Circuit supervised for Circuit not supervised for and is not power The Single Input Signal and the 2 CTM must installed in the same room three feet of each other INFORMATION City Tie Module 2 CTM is designed for use with controllers The 2 CTM is an interface between a Input Signal Module or a Dual Input Signal Module and Master Box It provides off premise signal transmission for which must comply with the provisions of the NFPA 2 CTM is used to activate a local energy fire alarm box provides a 24 VDC alarm signal which is current limited 200 mA Box Operation 24 VDC Wiring Resistance Current Current Current Gang Box 24 VDC 200mA SHEET 2 1 Tie Module into 14.5 Coil SHEET P N 270496 NAME 270496 CDR LEVEL 1.2 08 22 97 BY SJ BY MR UNIT OF GENERAL SIGNAL BUILDING SYSTEMS BUILDING SYSTEMS CORPORATION Parkland Drive FL 34243 6th Street East Sound ON Canada INFORMATION Fire Alarm Station 270 Series is a component of the Signature It is a normally open dry contact signal initiating device that only one action by the user in order to initiate an alarm The input module mounted to the back of the unit supervises the and sends an alarm signal to the loop controller when the is closed i e when the handle is pulled Cast zinc with steel backplate mechanism Single action pull lever voltage range 15.2 19.95 Vdc current 250 A current 400 A addressing temperature range 32 to 120 0 to 49 device address is required The loop controller assigns an to the station automatically A custom address can be to the station via laptop computer no addressing switches used humidity range 0 93 RH glass rods P N 276 GLR pkg 20 rods P N 27165 pkg 12 rods temperature range 4 to 140 20 to 60 LEDs provide visible indication of the status of the station the unit is removed from the electrical box electrical boxes Green LED flashes Red LED flashes terminal blocks will accept AWG 12 14 16 or 18 wire 2.5 1.5 or 0.75 sq mm Sizes 16 and 18 are preferred controller capab