EST F-DACT info

GE Life Safety Digital Alarm Communicator Sheet factory installed warning label must be removed the F DACT F line two phone jack A second phone line independent of that used for line must be connected to phone jack two F DACT F must be programmed for dual line F DACT F must be programmed to transmit a test at least once every 24 hours the JP1 wire loop intact configures the F DACT F attended downloading The panel will not allow changes the panel or dialer configuration unless the program is inserted It will allow changes to receiver account code telephone numbers etc UL the red wire loop to be intact for all remote station additional download security the F DACT F can be to perform a callback function to prevent access to the panel programming F DACT F is listed for use with the digital alarm receivers listed below 2000 4 2 Contact ID Knight MLR2 MCDI 4 2 Contact ID 4 2 Contact ID 4 2 4 2 4 2 Contact ID 4 2 Contact ID F DACT F is a digital alarm communicator transmitter F series fire alarm control panels The F DACT F also a dialer transmits system status changes events to compatible digital alarm communicator receiver over the switched telephone network The dialer is capable of reporting to two different account and telephone addition to dialer functions the F DACT F provides An LCD to display event messages and programming An event history log of panel and DACT events A modem for uploading and downloading panel history and current status to a PC compatible software The F DACT F modem is only rated for 2400 baud Some PC modems may not be compatible this baud rate F DACT F can be programmed to operate as a single or line DACT Modem LCD display a Modem LCD display an LCD display only For the F DACT F to be NFPA 72 CS the following are required 3101038 REV 1.0 ISS 11JAN07 of 5 Canada Information This equipment meets the applicable Industry Terminal Equipment Technical Specifications This confirmed by the registration number The abbreviation before the registration number signifies that registration performed based on a Declaration of Conformity that Industry Canada technical specifications met It does not imply that Industry Canada approved equipment installing this equipment users should ensure that it permissible to be connected to the facilities of the local company The equipment must also be using an acceptable method of connection The should be aware that compliance with the above may not prevent degradation of service in some to certified equipment should be coordinated by a designated by the supplier Any repairs or made by the user to this equipment or malfunctions may give the telecommunications cause to request the user to disconnect the should ensure for their own protection that the ground connections of the power utility lines and internal metallic water pipe system if are connected together This precaution may be important in rural areas Users should not attempt to make connections but should contact the appropriate electric authority or electrician as appropriate The Ringer Equivalence Number REN for this equipment is 0.1 The REN assigned to each equipment provides an indication of the maximum of terminals allowed to be connected to a interface The termination on an interface may of any combination of devices subject only to the that the sum of the Ringer Equivalence of all the devices does not exceed five EST 4 2 is SIA DCS 02 P3 with the ability to transmit hexadecimal codes Information The dialer complies with Part 68 of the FCC rules The FCC certification number and Ringer Number REN are displayed on the panel label and in this manual This information be provided to the telephone company if Two FCC compliant telephone cords with 8 pin modular at both ends are supplied with the FSDACT The is designed to be connected to the telephone using the supplied cord and an RJ 31X or RJ jack which must also comply with FCC Part 68 The REN is used to determine the maximum number of that may be connected to a single telephone All telephone devices are assigned a REN The of the RENs for all connected devices may not five The maximum REN may vary in some Contact the local telephone provider for more the dialer causes harm to the telephone network the company will notify you an advance that discontinuance of service may be required advance notice is not practical the telephone will notify you as soon as possible You will be advised of your right to file a complaint with the if you believe it is necessary The telephone company may make changes in its equipment operations or procedures that affect the operation of the dialer If this happens telephone company will provide advance notice in for you to make necessary modifications to uninterrupted service trouble is experienced with the dialer for repair or information contact the manufacturer at 739 4200 If the dialer is causing harm to the network the telephone company may you disconnect the dialer until the problem is No repairs may be performed on the dialer by the user The dialer can not be used on public coin phones or line service provided by the telephone company of 5 3101038 REV 1.0 ISS 11JAN07 1 F DACT F installation instructions the F DACT F according to the instructions provided High voltages capable of causing personal including death may be present Disconnect all of power then wait at least 30 seconds for to discharge to a safe energy level before Failure to disconnect power will damage the panel the F DACT F Observe static sensitive handling It is not necessary to remove the main panel board the cabinet to install the the F DACT F install the F DACT F Remove the clear plastic film protecting the LCD on the this is a new installation remove the insert from the window on the control panel Connect the power cable to J2 on the control panel Connect the supplied modular phone cables to the jacks See Figure 2 Energize the control panel programming instructions refer to the technical referenced under Protected Premises Unit on the label attached to the inside of the door addition if you are installing the F DACT F in a FireShield panel see for FireShield control later in this document Figure 1 Mount the F DACT F to the back of the circuit board 2 Typical RJ 31X connection premises down block 1 Line 2 1 jack LINE 2 jack block by installer 4 conductor cord 3101038 REV 1.0 ISS 11JAN07 of 5 for FireShield control panels you are installing the F DACT F into a FireShield control you will see these new programming options For DST End Day enter the day that DST ends The value is Sunday For DST End Hour enter the hour that DST ends The value is 02 2 00 a m Daylight saving time 1 and Line 2 supervision duration Blind call dialing ground fault check instructions for these new options are below saving time daylight saving time DST option determines when and much the system clock is adjusted for daylight saving default DST settings adjust the system clock forward hour on the second Sunday in March at 2 00 a m and one hour on the first Sunday in November at