Kidde Edwards Data Sheet K85001-0545 - Signal Master

S5389 or more pending Features Compatible with Genesis and Enhanced Integrity products Provides UL 1971 compliant synchronization for all strobes on same circuit Delivers independent horn control for horn strobes over two Genesis circuits Two methods of horn control available NAC signal silence or normally closed contact Convenient snap on or single gang remote models Only one module required per circuit 3 amp rating EG1M RM only Master Series Signal Master is a simple to use accessory that adds en features to Genesis strobes and horn strobes as well Enhanced Integrity strobes It is a dual purpose module that precision synchronization for connected strobes and control for connected Genesis horns over a single of wires Genesis and Enhanced Integrity strobes are self synchronizing installed with the Signal Master strobe flashes from devices the same circuit are synchronized to within 10 milliseconds of other indefinitely This exceeds the latest UL 1971 require in effect as of November 2000 which specify this level of over only two hours installed with Genesis horn strobes the Signal Master independent horn control on off and coded signals over single pair of wires Two methods of horn control are available NAC signal silence or normally closed contact Both may be used to silence horns without turning off strobes the same circuit Note independent horn control is available for only EG1 P Series steady horns are not compatible this feature mounting options ensure trouble free installation of the Signal Module The piggyback model doesn require separate electrical box It simply snaps to the back of the first on the circuit The remote mount model mounts in a North 2 inch 64 mm deep one gang box It may also be to any GSA MP mounting plate or directly to the rails inside MIRBPS Remote Booster Power Supply cabinets 1 of 4 D A T A S H E E T K85001 0545 to be used for installation purposes Issue 1 Catalog u Strobes Horns Bells ChimesTechnology that saves livesfirealarmresources com B Wiring Strobes Strobes or Enhanced Integrity Strobes Master silence and synchronization with two NACs Horn Strobes Horn Strobes Signal Master next device end of line 1 Input only 2 Input coded Master mount Master mount Master Only one Signal is required for horn strobe or circuit The strobe circuit of Signal Master a dedicated Strobe NAC must be con in alarm mode The Horn circuit of the Master can be with other Signal Master on one NAC When determin allowable wire refer to rating of Genesis Signal the signaling and the control specifications synchronization allowable between two devices in the viewing area is Ohms Silence and synchronization with one NAC and one dry contact Horn Strobes Horn Strobes Signal Master next device end of line CR must be installed within three feet of the G1M 1 Input only Loop 1 Input Master 3 2 1 next device or resistor 3 2 1 mount Master in in out out CR and wire nut be located in the same or Booster Power Supply cabinet Horn Strobes with one NAC Horn Strobes Master mount Master Integrity Horn strobes and Speaker strobes mount Master 2 of 4 Integrity Speaker Strobes Integrity Horn Strobes mount Master D A T A S H E E T K85001 0545 to be used for installation purposes Issue 1 A Wiring A wiring requires the GSA UM or GSA MAB A with Horn Silence using GSA MAB and GSA MCR modules A without Horn Silence using a GSA MAB module Horn Strobe Horn Strobe with Signal Master In Circuit Out Horn or Horn Strobe Horn Strobe with Signal Master Horn or 2 3 4 2 3 4 series 1 Out 1 In 2 3 4 1 In 1 Out the jumpers adjacent that use the riser In Circuit Out 2 3 4 series 1 Out 1 In 2 3 4 1 In 1 Out A with Horn Silence using GSA UM and GSA CR modules A without Horn Silence using a GSA UM module Horn Strobe Horn Strobe with Signal Master Horn or Horn Strobe Horn Strobe with Signal Master Horn or used 13 3 2 1 12 11 10 9 Module Relay next device out out out out 7 6 5 4 3 2 1 7 6 5 4 3 2 1 control panel next device or EOL resistor control panel next device or EOL resistor in in Signature Controller Previous Device in in Signature Controller Previous Device next device out out out out used 13 3 2 1 12 11 10 9 Module 3 of 4 D A T A S H E E T K85001 0545 to be used for installation purposes Issue 1 that saves lives us kidde fire fs utc com Kidde com EngineeredSystems is a UTC brand Corporate Park Drive NC 27302 2016 United Technologies Corporation rights reserved electrical box plate white ALARM the EG1M RM in a North one gang box 3 H x W x 2 D 95 mm x 5.1 mm x mm It may also be mounted MIRBPS Booster Power or on a GSA MP mount plate the EG1M Signal Master by the spade connectors into the on the back of the signal piggyback model to back Genesis device mount model American one gang boxes H x 2 W x 2 D 95 mm x mm x 64 mm and 1 inch mm deep 4 inch square boxes one gang covers and mounting plates Connections Rating Listings Approvals to 12 AWG 0.75 mm to 2.5 mm amps maximum amps maximum 1971 UL 1638 UL 464 ULC S525 ULC S526 MEA FM CE FCC flash per second within 10 milliseconds indefinitely UL 1971 requirements voltage Draw temperature range humidity range independent 2 wire horn control is available for horn strobes only EG1 P Series steady horns are not with this feature 33 Vdc 16 33 Vfwr 120 0 49 93 RH mA Information Number Description Signal Master Snap on piggyback Signal Master Remote Mount 1 gang Mounting Bracket allows for two 1 gang modules in a 2 gang box Wt lbs kg 0.1