Kidde Edwards Data Sheet K85001-0598 - 700 Sereis Self-Diagnostic Smoke Detectors

Two and Four Wire Terminal Smoke Series brand conventional photoelectric smoke detectors include interchangeable head and base with a light scattering optical They provide outstanding stability and excellent response a wide range of fires pulsed infrared LED light source and a high speed photodiode element are housed in an omnidirectional sensing cham protected by an insect screen For easy cleaning the detector a field replaceable optical chamber 721UT photoelectric detectors include integral fixed and rate of rise heat detectors The 721UT provides alarm and trouble LED driver outputs Also available is 713 5U electronic heat detector head for areas too dusty for detection Series smoke detectors were the industry first conventional detectors specifically designed for the demands of and industrial environments If the detector drifts out its UL Listed sensitivity range or fails internal diagnostics the LED flashes once a second to indicate a trouble condition meets NFPA 72 field sensitivity testing requirements without need for external meters diagnostic information is activated by applying a magnet the detector integral reed switch This initiates a self diag nostic and provides visual indication of sensitivity level or if service required The magnet test causes the LED to blink The number of counts corresponds to a smoke detector sensitivity range if they become dirty over time the 700 Series detectors adjust the alarm threshold through built in drift com If the detector ever does need to be cleaned the pat field replaceable optical chamber makes cleaning a snap Features Self diagnostic capabililty continually monitors operation Meets NFPA 72 sensitivity test requirements Head and terminal base design base sold separately Automatic drift compensation Field replaceable optical chamber Low profile design blends into the ceiling Advanced alarm verification nuisance alarm immunity Continuity switch in base to ease installation Extensive two wire compatibility listings Specifications 700 Series photoelectric smoke detector is a low profile self two wire detector that monitors its own sensitivity and status The detector meets NFPA 72 field sensitivity requirements without the need for external meters Built in compensation automatically adjust the sensitivity if the detec gets dirty The 700 Series features an alarm verification feature further reduce the chance of a nuisance alarm Normal sensing every 9 seconds This rate doubles when a signal exceed the alarm threshold value is sensed Two additional successive above the threshold level initiate an alarm The patented sensing chamber is field replaceable allowing quick and cleaning and maintenance manually operated switch between terminals 1 and 2 establishes across the alarm initiating circuit at initial installation of base simplifying testing without the smoke head in place The automatically opens when a detector head is plugged in D A T A S H E E T K85001 0598 to be used for installation purposes Issue 1 1 of 2 Catalog u Conventional InitiatingTechnology that saves livesfirealarmresources com that saves lives us kidde fire fs utc com Kidde com EngineeredSystems is a UTC brand Corporate Park Drive NC 27302 2016 United Technologies Corporation rights reserved Specifications ripple peak to peak standby current 24V alarm current 24V Sensitivity temperature humidity range immunity LED output current compensation adjustment Sensor Ratings 741UT 713 5U wind velocity wiring size test input 721UT voltage time two wire compatibility identifier 33VDC non polarity sensitive Vp p to 60 mA max if not limited by control panel 0.37 1.00 to 120 0 to 49 to 95 Non condensing V m min 0 1000 MHz mA min 8.5 mA max max 711U Bases 701U 702U 135 Rate of rise 15 105 8.3 ft min or AWG ohm max max second max 711U 721UT 713 5U 731U head dimensions dimensions height head and base head and base D x 1.75 H 10cm x 4.44cm 702U 6 D x 06 H 15.24 cm x 1.3 cm 5 cm H 268 FM CSFM MEA approved Information detector head only photoelectric two wire detector head only photoelectric two wire heat output for remote LED detector head only photoelectric two wire 702RU base for aux relay functionality detector head only photoelectric four wire detector base 3 terminals 6 dia detector base 6 terminals 6 dia detector base 6 terminals aux relay 6 dia Bases sold separately 702U 2 of 2 D A T A S H E E T K85001 0598 to be used for installation purposes Issue 1