Faraday FWIIplus2, (4 Zones)

FARADAY 15240A ALARM CONTROL UNIT MANUAL 445926 I Rev C S Maumee St Tecumseh MI 49286 517 423 2111 Fax 517 423 2320 1998 Faraday LLC All Rights Reserved OF CONTENTS AND WARRANTY INFORMATION PERFORMANCE PARAMETERS I FIRE ALARM SYSTEM CONTROL UNIT SEMI FLUSH TRIM 6 A H BATTERY SET 10 A H BATTERY SET 15 A H BATTERY SET BATTERY CABINET REMOTE ANNUNCIATOR MODULE MARCH TIME TEMPORAL SIGNALING MODULE ZONE RELAY MODULE CITY TIE MODULE CITY TIE AUXILIARY RELAY MODULE AUXILIARY RELAY MODULE D A C T INTERFACE MODULE SPECIFICATIONS II INSTRUCTIONS OPERATION INDICATIONS SILENCING SILENCING RESET OPERATION INDICATIONS SILENCING SUPERVISORY OPERATION INDICATIONS SILENCING AND L E D FUNCTIONS TESTING AND MAINTENANCE OPERATING INSTRUCTIONS III INSTRUCTIONS QUAILIFIED PERSONNEL ONLY CONTROL UNIT INSTALLATION WIRING DIAGRAM WIRING DIAGRAM DIAGRAM FOR HEAT DETECTORS PULL STATIONS DIAGRAM FOR SUPERVISORY SWITCHES DIAGRAM FOR WATERFLOW SWITCHES 2 WIRE SMOKE DETECTORS DIAGRAM FOR SYSTEM SENSOR 2 WIRE DETECTORS DIAGRAM FOR SYSTEM SENSOR 2 WIRE DUCT DETECTORS 4 WIRE SMOKE DETECTORS III INSTALLATION INSTRUCTIONS CONTINUED QUAILFIED PERSONNEL ONLY DIAGRAM FOR SYSTEM SENSOR 4 WIRE DETECTORS DIAGRAM FOR SYSTEM SENSOR 4 WIRE DUCT DETECTORS DIAGRAM FOR SYSTEM SENSOR 4 WIRE BEAM DETECTORS SIGNALS DIAGRAM FOR SIGNAL CIRCUIT SELECTION GUIDES SIZE CALCULATIONS REMOTE ANNUNCIATOR MODULE MARCH TIME TEMPORAL SIGNALING MODULE ZONE RELAY MODULE CITY TIE MODULE CITY TIE AUXILIARY RELAY MODULE AUXILIARY RELAY MODULE SUPERVISORY MODULE D A C T INTERFACE MODULE TRANSMITTER CONNECTIONS IV GUIDE QUAILIFIED PERSONNEL ONLY TROUBLESHOOTING MODULE BOARD TROUBLES MODULE TROUBLES INSTALLATION AND WARRANTY INFORMATION INFORMATION The Manufacturer provides a limited warranty for one year from the date of purchase to the Purchaser of this product The Original Purchaser is the party to whom the Manufacturer issued its Sales Order the Manufacturer distribution in order to preserve this warranty it is important that the product be serviced only persons who have been properly trained and authorized by the Manufacturer parties involved in the installation of this product may have also provided a warranty which may be different than of the manufacturer The Manufacturer will only be responsible to the Original Purchaser and only for the own warranty For further information regarding the Manufacturer warranty contact the Original MANUAL The owner manual does not purport to cover all the details or variations in the equipment nor does it provide for every possible contingency to be met in connection with installation operation and All specifications subject to change without notice Should further information be desired or should problems arise which are not covered sufficiently the matter should be referred to the Installer or Original listed below INFORMATION INSTALLED INSTALLER SIGNATURE PURCHASER INFORMATION PURCHASE ORDER NO PURCHASED SALES ORDER ACKNOWLEDGMENT NO PURCHASER SIGNATURE A COPY OF THE ABOVE COMPLETED INFORMATION MAY BE REQUIRED BY THE MANUFACTURER AUTHORIZATION OF WARRANTY SERVICES with the use of this Instruction Manual the appropriate following standards and the manufacturers instructions for and signaling devices should be used to install and maintain a functioning Fire Alarm Signaling System 70 1993 72 1993 Electrical Code 1993 Electrical Code 1993 Electrical Code 1993 Electrical Code 1993 Electrical Code 1993 Fire Alarm Code Fire Alarm Code Fire Alarm Code Fire Alarm Code Fire Alarm Code 101 1993 Safety Code Safety Code Safety Code Safety Code Safety Code STANDARDS Contact other standards other standards other standards other standards other standards may apply may apply may apply may apply may apply PUBLICATIONS CONTACT Fire Protection Association Park MA 02269 PERFORMANCE PARAMETERS control panel will not show an alarm condition without compatible initiating devices smoke detectors and indicating devices horn lights etc connected to it Electrical ratings of the initiating and indicating must be U L listed compatible with the electrical ratings of the control panel and must be properly The wiring used for interconnection must be large enough to carry the total current by all without excessive voltage drop panel must be connected to a dedicated primary electrical source of 120VAC 60Hz that has a high of reliability and adequate capacity for this panel The only means of disconnecting this power source be available only to authorized personnel and clearly marked Alarm Circuit Control panel must also have connected to it a battery set 24V that has enough capacity to properly operate system for 24 hours standby and 5 minutes alarm per NFPA 72 or 60 hours standby and 5 minutes alarm NFPA 72 These batteries do lose capacity with age Batteries must be replaced when they fail to provide panel with the required standby and alarm power or 4 years whichever happens first These batteries be checked for performance at least 2 times per year or more often if local requirements dictate it regular test program should be followed and documented to make sure that each part of the system is as per NFPA 72 or more often if dictated by local code requirements Malfunctioned units must be or repaired immediately by factory authorized service personnel This panel is designed to show an alarm condition when the initiating devices connected to it detect conditions These conditions may or may not represent a life threatening condition ie burnt toast not be a life threatening condition but may cause an initiating device to indicate an alarm condition Also of a building or area unnecessarily may subject individuals to an unnecessary hazard Therefore is most important that building owner manager or representative promulgate distribute and or post describing steps to be taken when the fire alarm panel signals an alarm condition These should be developed in cooperation and conformance with representatives of the local authority jurisdiction a backup or precautionary measure it is strongly suggested that one of these steps should be to the local fire department even where the city tie option or similar device is included in the 15220A Two Zone and 15240A Four Zone Fire Alarm System Control Unit provides manual automatic waterflow alarm and supervisory service Zone 1 may be used as a manual automatic or waterflow initiating or it can be programmed to be used with normally open sprinkler supervisory switches Zone 2 may be used a manual automatic or waterflo