Farenhyt IPGSM-4G IP & Cellular Communicator

IP Internet GSM 4G 3G 2G Path Communicator IPGSM 4G is a 4G fire alarm communicator that offers ID reporting with any Fire Alarm Control Panel that has a built in dialer This easy to install dual communicator connects directly to the primary and communication ports of a Fire panel Digital Communicator Transmitter DACT It offers three reporting paths which include Cellular only IP or IP primary cellular backup In the event of an off condition the fire panel sends contact ID formatted to the IPGSM 4G communicator panel The then reformats the data into highly encrypted packets for transmission to the Alarm Net receiver customer provided Internet Intranet connection or the network communication methods are critical in the due to VoIP Voice over IP migration from Plain Old Telephone Service and growth of digital networks The IPGSM 4G exclusive dual path solution combines Internet service with GSM added reliability and an extra level of security All signals the IPGSM 4G communicator panel are delivered to AlarmNet Network Control Center which routes information to the appropriate central station The state of art AlarmNet network control center is fully redundant and 24 7 AlarmNet has the ability to route messages AlarmNet i and 800 PLUS services providing true and multipath message delivery IPGSM 4G is designed to operate over the most GSM networks including 2G 3G and 4G Its multi platform technology automatically chooses the best cellular signal in the area based on signal strength seamlessly self adjusts to maintain critical life safety the Internet or GSM radio the provides full data reporting and is listed with the Silent Knight systems IFP Series System 5820XL 5808 and 5700 Any DACT using Contact ID reporting Saves the cost of two dedicated phone lines Dual path communications Can communicate to central using Internet or cellular technology Requires no change to the existing Fire Alarm Control Panel The IPGSM 4G connects directly to the and secondary telephone ports Listings Multi GSM platform compatibility for 2G 3G 4G Operates over the following communication HSPA 4G HSPA HSDPA 3G EDGE 2G GPRS 2G Works over any type of customer provided 10 100 Base network connection LAN or WAN modem or cable modem Data transmits over standard contact ID but is secured with the industry encryption standard AES 256 bit Supports both dynamic DHCP or Public and Static IP addressing Built In Power Supply module On board circuit design accommodates back battery Includes primary power and supervision Diagnostic LEDs Signal strength and status Reliable connection IP and GSM connection every day QOS Quality of Service diagnostics via conveys vital communicator including when message was signal strength and message path 7720P Hand held programmer for easy 350929 Rev A 2013 Honeywell International Inc an event occurs the Fire Alarm Control Panel goes hook to dial the central station The IPGSM 4G Dialer Module detects the off hook condition and the fire panel with a dial tone When the fire detects the dial tone it begins dialing the central After the dialing is completed the Dialer Capture returns a handshake to the fire panel The fire then sends the contact ID reports to the Dialer Module which in turn sends a kiss off after the is successfully received from the fire panel The Capture Module sends the contact ID reports to the communications module When all the reports are the fire panel goes on hook The IPGSM module then transmits the messages to central station either over the GSM network or the dependent on configuration to Program IPGSM 4G communicator can be pre programmed the 7720P programmer to enter all central station This is saved to the IPGSM 4G communicator memory When the IPGSM 4G communicator is at the site and connected to the Internet Intranet registers itself with the AlarmNet receiver most installations the only required parameters are Primary City ID two digits obtained from your station Primary Central Station ID two digits obtained from monitoring station Primary Subscriber ID four digits obtained from your station Communication Module MAC ID and MAC CRC located on outside of box and inside of the of these parameters are assigned by the monitoring Some assembly is required See Installation and Guide 800 12454 for full details Requirements COMPLIANCE meet UL864 NFPA ensure the following IPGSM 4G must be installed in accordance with NFPA Fire Protection Association standards 70 and IPGSM 4G must be mounted in the same room and 20 feet of the fire panel IPGSM 4G and all equipment used for the IP such as the router hub modem etc be listed must be powered from an un switched circuit and be provided with appropriate power IPGSM 4G must use the 7AH battery not supplied to 24 hour backup capability 120VAC 60Hz 0.5A Secondary 18VDC One 12 V 7.0 AH lead acid battery not charging current 1 Amp maximum discharge current Standby 230mA Active 14.875 H x 12.75 W x 3.0 D cm H x 32.4cm W x 7.6 cm D Red 5.3lbs Temperature 32 F to 120 F C to 49 C 0 90 non condensing Listings and Approvals listings and approvals below apply to the basic communicator panel In some cases certain may not be listed by certain approval agencies listing may be in process factory for latest listing status Listed Information Internet and Digital Cellular Fire Alarm Panel Includes red cabinet with ademco and lock wall outlet box Dialer Capture Module Communications Module antenna mounting PowerBoost1 power supply LED display board manual required screws cables etc 3db gain external remote antenna 50 ft antenna cable low loss 25 ft antenna cable low loss SNA to N Adapter IPGSM 4G hand held programmer Plug in transformer box for IPGSM Battery 12 Volts 7 AH sealed document is not intended to be used for installation purposes We try to keep our information up to date and accurate We cannot cover all specific applications anticipate all requirements All specifications are subject to change without notice more information contact Silent Knight 12 Clintonville Road Northford CT Phone 800 328 0103 Fax 203 484 7118 For Technical Support call 800 446 6444 www farenhyt com in the U S A