DSC DM-W DM-C - Installation Manual - English - Wall-Mount Ceiling Mount Bracket (Compatible with Force 2 detectors)

File Preview
File Preview
Click below to download for free

Text Preview

DM C Motion Detector Mounting Bracket You Begin all instructions before beginning installation Be sure to read instructions that came with your motion detector to ensure proper that coverage vs angle settings as described in your motion instructions may not apply when a bracket is used It is that the detector circuit board position be set for the nomi 8 adjustment the factory setting as noted in the detector in When attached to the DM C ceiling mounting bracket detector can be pointed up or down left or right by adjusting mounting bracket mounting plate mounting carefully follow the instructions provided with motion detector to test the detector to ensure adequate the Bracket DM C ceiling mounting bracket can be mounted on a standard electrical box or can be secured directly on the ceiling To secure the bracket directly to the ceiling first place the bracket at the desired location and mark the location of the mounting screws Drill these locations and insert plastic screw into the ceiling an opening in the ceiling and bring wires through the open Prepare the wires for connection to the motion detector Feed wires through the wire path opening in the bracket swivel as shown in Figures 1 and 2 Be sure to feed enough through the bracket so that the wires do not accidentally slip into the ceiling the bracket with the two painted screws provided and tilt the backplate to the desired position and tighten the screw You may wish to leave the locking screw somewhat to allow adjustment of the backplate during testing of the When all the tests have been completed and the results are remove the motion detector from the backplate and tighten the locking screw The backplate should not move the locking screw is completely tightened 1 PATH WIRES THROUGH AS SHOWN FROM PANEL 2 Mounting Bracket Side View to the instructions included with your motion detector the back of the detector Remove the upper wiring knock and the screw knockouts corresponding to the mounting on the backplate the wires through the wiring knockout in the motion detec back and secure the back to the backplate It is recommended initial testing be done with only one screw holding the de to the backplate With only the upper left or right screw the detector may be easily rotated to provide access to locking screw When testing is complete tighten the locking and secure the detector back to the backplate with the screw the wires to the detector following the instructions pro with your motion detector When wiring is complete reas the motion detector test coverage of the detector carefully following the provided with the detector Reposition the detector rotating and tilting the backplate Mounting Bracket Top View Digital Security Controls Ltd Canada www dsc com Support 1 800 387 3630 in Canada 29000344 R002 Motion Detector Mounting Bracket You Begin all instructions before beginning installation Be sure to read instructions that came with your motion detector to ensure proper that coverage vs angle settings as described in your motion instructions may not apply when a bracket is used It is that the detector circuit board position be set for the nomi 8 adjustment the factory setting as noted in the detector in When attached to the DM W wall mounting bracket the can be pointed up or down left or right by adjusting the bracket mounting plate mounting carefully follow the instructions provided with motion detector to test the detector to ensure adequate the Bracket DM W wall bracket can be mounted on a single gang electrical or can be secured directly on the wall surface To secure the directly to the wall first place the wall bracket at the desired and mark the location of the two mounting screws Drill locations and insert plastic screw anchors into the wall an opening in the wall and bring wires through the opening the wires for connection to the motion detector Feed the through the wire path opening in the bracket swivel mecha as shown in Figures 1 and 2 Be sure to feed enough wire the bracket so that the wires do not accidentally slip back the wall the bracket with the two painted screws provided and tilt the backplate to the desired position and tighten the screw You may wish to leave the locking screw somewhat to allow adjustment of the backplate during testing of the When all the tests have been completed and the results are remove the motion detector from the backplate and tighten the locking screw The backplate should not move the locking screw is completely tightened to the instructions included with your motion detector the back of the detector Remove the upper wiring knock 1 2 FROM PANEL WIRES THROUGH AS SHOWN Mounting Bracket Side View and the screw knockouts corresponding to the mounting on the backplate the wires through the wiring knockout in the motion detec back and secure the back to the backplate It is recommended initial testing be done with only one screw holding the de to the backplate With only the upper left or right screw the detector may be easily rotated to provide access to locking screw When testing is complete tighten the locking and secure the detector back to the backplate with the screw the wires to the detector following the instructions pro with your motion detector When wiring is complete reas the motion detector test coverage of the detector carefully following the provided with the detector Reposition the detector rotating and tilting the backplate PATH Mounting Bracket Back View Digital Security Controls Ltd Canada cid 127 www dsc com Support 1 800 387 3630 in Canada 29000344 R002

Related Files