
File preview
Click below to download immediately for free
File data
- Filename: 5632718490_DSC_GS-15_25_50ANTQ_Placement_and_Installation_Instructions.pdf
- File size: 994 KB
- File type: pdf
- Download count: 59
Text Preview
GS-15/25/50ANTQ Placement and Installation Instructions Type Frequency Bands Beamwidth Beam width (3dB) (max.) Weight, inc Cable (lb/kg) Length/Diameter (inch/mm) Cable Length (ft/m) type Cable Length (inch) types Dipole & 850/1900 Ohms / 0.37kg / 4.5m (Male) Dipole Dipole (low/high band) (low/high band) & 850/1900 & 850/1900 ohms / 1kg / 7.6m (Male) ohms / 2.3kg / 15.2m (Male) / 0.46″(12mm) / 0.79″(20mm) / 0.79″(20mm) (Female) to MMCX (Male) SMA (Female) to MMCX (Male) (Female) to MMCX (Male) A PANEL FOR GS INSTALLATION the TL260GS/GS2060 There are HAZARDOUS VOLTAGES up to 240VAC (40VA) and/or TNV circuits within the panel cabinet. down the system. the supplied white whip antenna from the panel cabinet by rotating the base of the antenna anti-clockwise. the brass nut holding the threaded section remains and is tight. the cabinet front cover to allow visibility of the green signal strength LEDs on the communicator board. the free cable end of the extension antenna onto the extension antenna screw. down the rubber sleeve on the extension antenna cable over the connection point (see picture). up the unit by connecting at the mains. strength LEDs with antenna removed nut TL260 fitting cable sleeve Extension antenna connected These instructions shall be used in conjunction with the TL260GS/TL265GS/GS2060/GS2065 Instal- Manual. Disconnect power and telephone lines during the installation of the GS-15ANTQ, GS-25ANTQ GS-50ANTQ antennas. The GS-15ANTQ, GS-25ANTQ and GS-50ANTQ antennas shall be used only in con- with the supplied coaxial cable. The GS-15ANTQ, GS-25ANTQ and GS-50ANTQ antennas shall be by service persons only. Use caution when installing the GS-25ANTQ and GS-50ANTQ antennas near lines. The outside antenna system should not be located in the vicinity of overhead power lines or electric light or power circuits, or where it can fall into such power lines or circuits, as contact with might be fatal. NEVER install the antenna during a lightning storm. When installation is complete, ver- that the mounting is secure and the connector is properly attached. Ensure the antenna installation is the TL265GS/GS2065 the front cover of the panel. power to the panel by disconnecting the mains and disconnecting the back-up battery by removing the RED (+) con- from the battery. the extension antenna plug cap located on the top right of the panel enclosure. the existing PCB antenna cable from the communicator in the following sequence. the cable from the radio module by inserting a small, flat head screwdriver between the cable and the radio mod- then gently pry the plug loose. Use a pair of pliers to grip the head of the cable connector closest to the PCB antenna and pull away from the board. (Note: other method for removal of this connector may cause permanent damage to the on-board connector.) the 12.7cm (5 antenna cable supplied in the antenna kit. the small plug end of the cable into the radio module and push firmly to ensure the cable connector fully engages. the brass nut and washer from the other end of the cable and insert the screw thread through the hole in the top right the panel. the washer and nut on the screw thread and tighten it with your fingers. the free cable end of the extension antenna onto the threaded brass connector that exits the top right of the panel Ensure the connection is tight. down the rubber sleeve on the extension antenna cable over the connection point. the battery RED (+) connector. up the unit by reconnecting it at the mains.