DSC HS-AH600 - Installation Manual - English - Concourse Audio Distribution Module

File Preview
File Preview
Click below to download for free

Text Preview

Warranty Security Controls Ltd warrants that for a period of 12 months from the date of purchase the product be free of defects in materials and workmanship under normal use and that in fulfilment of any breach such warranty Digital Security Controls Ltd shall at its option repair or replace the defective equipment return of the equipment to its repair depot This warranty applies only to defects in parts and and not to damage incurred in shipping or handling or damage due to causes beyond the of Digital Security Controls Ltd such as lightning excessive voltage mechanical shock water or damage arising out of abuse alteration or improper application of the equipment foregoing warranty shall apply only to the original buyer and is and shall be in lieu of any and all other whether expressed or implied and of all other obligations or liabilities on the part of Digital Controls Ltd Digital Security Controls Ltd neither assumes nor authorizes any other person to act on its behalf to modify or to change this warranty nor to assume for it any other warranty liability concerning this product no event shall Digital Security Controls Ltd be liable for any direct indirect or consequential damages loss anticipated profits loss of time or any other losses incurred by the buyer in connection with the purchase or operation or failure of this product detectors can only detect motion within the designated areas as shown in their respective installation They cannot discriminate between intruders and intended occupants Motion detectors do not volumetric area protection They have multiple beams of detection and motion can only be detected unobstructed areas covered by these beams They cannot detect motion which occurs behind walls floor closed doors glass partitions glass doors or windows Any type of tampering whether or unintentional such as masking painting or spraying of any material on the lenses mirrors or any other part of the detection system will impair its proper operation infrared motion detectors operate by sensing changes in temperature However their effectiveness be reduced when the ambient temperature rises near or above body temperature or if there are or unintentional sources of heat in or near the detection area Some of these heat sources could heaters radiators stoves barbeques fireplaces sunlight steam vents lighting and so on Digital Security Controls Ltd recommends that the entire system be completely tested a regular basis However despite frequent testing and due to but not limited to criminal or electrical disruption it is possible for this product to fail to perform as expected INFORMATION Changes or modifications not expressly approved by Digital Security Ltd could void the user authority to operate this equipment Digital Security Controls Ltd Canada 1 800 387 3630 www dsc com in Canada 29005164 R001 Six Room Audio Module Instructions HS AH600 is a six room Audio Distribution Hub for use with the DSC Concourse Systems wiring solution This module can be installed in any of the Concourse Systems panels using the supplied mounting hardware Impedance matching controls and speakers not supplied will be required to complete the installation of Package installing the module confirm that the package contains the following parts one HS AH600 Audio Distribution Hub one HS MP200 mounting plate three plastic standoffs Instructions Insert the standoffs into the mounting plate as per Figure A matching the hole on the HS AH600 Audio Distribution Hub Mounting A Plate There are two possible placement positions Align the HS AH600 Audio Distribution Hub over the stand offs and snap into place Locate a suitable mounting location for the HS AH600 Audio Distribution Hub inside cabinet Align the two mounting tabs with the holes in the wire raceway and insert as per Figure B Figure B Snap the module into place by pushing the opposite side towards the back of the cabinet Instructions Run 2 pairs of speaker wire 10 AWG max from the cabinet to the audio amplifier from the cabinet to each desired speaker pair location Allow sufficient length at ends of the run to avoid stress and for proper termination and trim out Label all wires at both ends for easier identification Strip of insulation off the input speakers wires and insert into the input terminals the AH600 Audio Distribution Hub marked observing L and R pairing and phasing Strip of insulation off the output speaker wires and insert into the output up to six of the AH600 Audio Distribution Hub marked observing L R pairing and phasing At each of the speaker pair locations strip sufficient insulation off the output wires and connect to the impedance matching volume controls not following manufacturer instructions See Figure C At the audio amplifier strip sufficient insulation off the speaker wires that were run the cabinet Connect to the output terminals of the audio amplifier matching left right and phasing in step 2 Channels 1 Channels 6 Control Not Provided Matching Not Provided Not Provided Wire AWG 10 AWG Maximum 4.9 cm W x 9.2 cm L Diagram C Snap the module into place by pushing the opposite side towards the back of the cabinet Instructions Run 2 pairs of speaker wire 10 AWG max from the cabinet to the audio amplifier from the cabinet to each desired speaker pair location Allow sufficient length at ends of the run to avoid stress and for proper termination and trim out Label all wires at both ends for easier identification Strip of insulation off the input speakers wires and insert into the input terminals the AH600 Audio Distribution Hub marked observing L and R pairing and phasing Strip of insulation off the output speaker wires and insert into the output up to six of the AH600 Audio Distribution Hub marked observing L R pairing and phasing At each of the speaker pair locations strip sufficient insulation off the output wires and connect to the impedance matching volume controls not following manufacturer instructions See Figure C At the audio amplifier strip sufficient insulation off the speaker wires that were run the cabinet Connect to the output terminals of the audio amplifier matching left right and phasing in step 2 Channels 1 Channels 6 Control Not Provided Matching Not Provided Not Provided Wire AWG 10 AWG Maximum 4.9 cm W x 9.2 cm L Diagram C Security Controls Ltd warrants that for a period of 12 months from the date of purchase the product be free of defects in materials and workmanship under normal use and that in fulfilment of any breach such warranty Digital Security Controls Ltd shall at its option repair or replace the defective equipment return of the equipment to its repair depot This warranty applies only to defects in parts and and not to damage incurred in shipping or handling or damage due to causes be

Related Files